Huawei U8650 Скачать руководство пользователя страница 36

Страница: 36 / 101

U8950 Maintenance Guide V1.0

9 Maintenance Records During Verification

2012-10-22

Huawei Proprietary and Confidential

Maintenance Records During Verification

9.1 Maintenance Records on Each Stage

Stage

Station of Fault

Faulty Item

Symptom

Solution

Board upgrade

The upgrade
failed at 4%.

The data was lost.

The board was formatted and
reloaded and the test then passed.

Poor loading

The flash chip was
poorly soldered.

The software was reloaded and no
interface was detected. The test
passed after the flash chip was
heated and re-soldered.

Poor loading

The data was lost.

The board was formatted and
reloaded and the test then passed.

MMI06A
vibrator
malfunction

The vibrator was
faulty.

The faulty product was retained, as
required by the R&D department, for
analysis by the vendor.

MMI

MMI06A
vibrator
malfunction

The FPC and BTB
connector were not
fit in place.

The BTB connector was refitted.

MMI

MMI06A
vibrator
malfunction

The FPC BTB
connecting to the
antenna board was
bridged, resulting in
the grounding of
VIB_DRV_N. The
vibrator started
vibrating once the
battery was loaded.

The vibrator was re-soldered.

MMI

MMI05C
touchscreen
malfunction

The chip on the
touchscreen was
damaged.

The touchscreen was replaced.

Содержание U8650






































































































Результаты поиска

Содержание U8650

Отзывы:

Похожие инструкции для U8650

Бренды по названию

Популярные бренды

Huawei U8650, Руководство по обслуживанию

Результаты поиска

Содержание U8650

Отзывы:

Похожие инструкции для U8650

Бренды по названию

Популярные бренды