Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 65

Страница: 65 / 99

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Figure 4-4

Installing an SMU

----End

Follow-up Procedure

Pack the removed component and send it to the local Huawei warehouse.

4.4.3 Replacing an AC SPD

Prerequisites



An ESD wrist strap, ESD gloves, ESD box or bag, required tools, and cabinet door key
are available.



The new AC SPD is intact and the indication window is green.

Do not replace an AC SPD during a thunderstorm.

Procedure

Step 1

Connect the ground cable for the ESD wrist strap, and put on the ESD wrist strap and ESD
gloves.

Step 2

Push down on the faulty AC SPD and pull it out, as shown in Figure 4-5.

Step 3

Install the new AC SPD, as shown in Figure 4-5.

Содержание Telecom Power TP48200A-HT19C3




































































































Результаты поиска

Содержание Telecom Power TP48200A-HT19C3

Отзывы:

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренды по названию

Популярные бренды

Huawei Telecom Power TP48200A-HT19C3, Руководство пользователя

Результаты поиска

Содержание Telecom Power TP48200A-HT19C3

Отзывы:

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренды по названию

Популярные бренды