Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 99

background image

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Copyright © Huawei Technologies Co., Ltd.

59

Figure 4-5

Replacing an AC SPD

Step 4

Disconnect the ground cable for the ESD wrist strap, and remove the ESD wrist strap and
gloves.

----End

Follow-up Procedure

Check that the alarm for the AC SPD is cleared.

4.4.4 Replacing a Circuit Breaker

Prerequisites

Before replacing an AC circuit breaker, switch off the upstream input circuit breaker.



The cabinet door key, insulation tape, and required tools are available.



The new circuit breaker is intact and has the same specifications as the circuit breaker to
be replaced.

Procedure

Step 1

Switch off the circuit breaker that is to be replaced.

Step 2

Record the positions where the output cable and signal cable terminals connect to the circuit
breaker.

Step 3

Loosen the screw that secures the upper port of the circuit breaker using a Phillips screwdriver,
and remove the output power cable and signal cable terminals. Wrap the cable and terminals
using insulation tape.

Step 4

Loosen the screw that secures the lower port of the circuit breaker using a Phillips screwdriver,
and open the buckle at the base of the circuit breaker using an insulated flat-head screwdriver.

«
...
64
65
66
67
68
...
»

Содержание Telecom Power TP48200A-HT19C3




































































































Отзывы:

Нет отзывов

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренд: Makita Страницы: 60

Бренд: Quasar Страницы: 3

Бренд: FAR Страницы: 80

Бренд: Lambda Страницы: 56

Бренд: Lakeshore Страницы: 122

Бренд: U-Line Страницы: 6

Бренд: Erbauer Страницы: 78

Бренд: Porter-Cable Страницы: 32

Бренд: VONROC Страницы: 84

Бренд: Gardner Denver Страницы: 27

Бренд: BK Precision Страницы: 92

Бренд: HIKOKI Страницы: 24

Бренд: HySecurity Страницы: 2

NittaBeltPoly PI-30

Бренд: Nitta Страницы: 16

Бренд: Prince Castle Страницы: 4

Бренд: Rapid Страницы: 64

Бренд: Timberline Tool Страницы: 6

Бренд: Erbauer Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды