manualshive.com logo in svg

Huawei SUN2000 M0 Series, Руководство пользователя

Поделиться
Скачать
Huawei SUN2000 M0 Series Скачать руководство пользователя страница 47

5.4 Connecting the DC input power cable

Precautions

D ANGER

● Before connecting the DC input power cable, ensure that the DC voltage is

within the safe range (lower than 60 V DC), and that the DC SWITCH is set to

the OFF position. Failure to do so could generate high voltage, which may

cause electric shocks.

● When the SUN2000 is operating, it is not allowed to operate the DC input

power cable, such as connecting or disconnecting a PV string or a PV module in

a PV string. Failing to do so may cause electric shocks.

● If no PV string is connected to a DC input terminal of the SUN2000, do not

remove the watertight cap from the terminal. Otherwise, the IP rating of the

SUN2000 will be affected.

WARNING

Ensure that the following conditions are met. Otherwise, the SUN2000 may be

damaged, or even a fire could happen.
● PV modules connected in series in each PV string are of the same specifications.
● The open-circuit voltage of each PV string is always lower than or equal to

1100 V DC.

● The maximum short-circuit current of each PV string must be lower than or

equal to 15 A.

● The DC input power cable is correctly connected. The positive and negative

terminals of a PV module are connected to corresponding positive and negative

DC input terminals of the SUN2000.

● If the DC input power cable is reversely connected, do not operate the DC

switch and positive and negative connectors. Wait until the solar irradiance

declines at night and the PV string current reduces to below 0.5 A, and then

turn off the DC switch. Remove the positive and negative connectors to correct

the polarity.

NO TICE

● Because the output of the PV string connected to the SUN2000 cannot be

grounded, ensure that the PV module output is insulated to ground.

● During the installation of PV strings and the SUN2000, the positive or negative

terminals of PV strings may be short-circuited to ground if power cables are not

properly installed or routed. An AC or DC short circuit may occur and damage

the device when the SUN2000 is operating. The caused device damage is not

covered under any warranty.

SUN2000-(3KTL-10KTL)-M0

User Manual

5 Electrical Connections

Issue 06 (2020-10-23)

Copyright © Huawei Technologies Co., Ltd.

40

Содержание SUN2000 M0 Series


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды