Huawei SUN2000-33KTL Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 98

background image

SUN2000-(33KTL, 40KTL)
User Manual

8 Maintenance

Issue 03 (2015-12-01)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

80

Alarm ID Alarm

Name

Alarm
Severity

Causes

Measures

305

Frequency
Abnormal

Major

The actual frequency of the
grid is higher than or less than
the required value for the local
grid.

1.

If the alarm occurs accidentally,
possibly the power grid is
abnormal accidentally. The
SUN2000 automatically recovers
to the normal operating status
after the fault is rectified.

2.

If the alarm occurs repeatedly,
check whether the grid frequency
is within the allowable range. If
no, contact the local power
operator. If yes, change the grid
overfrequency and
underfrequency protection points
on the SUN2000 APP, data
collector, or NMS after obtaining
approval from the local power
operator.

313

Low Array
Insulation
Resistance

Major

The insulation resistance
against the ground for PV
strings is less than the
minimum value. The possible
causes are as follows:



A short circuit exists
between PV strings and
protection ground.



PV strings are installed in a
permanently moist
environment.

1.

Check the insulation resistance
against the ground for the PV
strings. If a short circuit has
occurred, rectify the fault.

2.

If the insulation resistance
against the ground is less than the
default value in a rainy
environment, set

Insulation

resistance protection

on the

SUN2000 APP, data collector, or
NMS.

318

Residual
Current
Abnormal

Major

The insulation resistance
against the ground at the input
side decreases during
SUN2000 operation, which
causes excessively high
residual current.

1.

If the alarm occurs accidentally,
possibly the external circuits are
abnormal accidentally. The
SUN2000 automatically recovers
to the normal operating status
after the fault is rectified.

2.

If the alarm occurs repeatedly or
lasts a long time, check whether
the insulation resistance against
the ground of PV strings is too
low.

321

Cabinet
Over-Tem
p

Major



The SUN2000 is installed
in a place with poor
ventilation.



The ambient temperature is
too high.



The internal fan is not
working.

Check whether the ambient
temperature of the SUN2000
exceeds the upper limit. If yes,
improve ventilation to decrease the
temperature.

«
...
84
85
86
87
88
...
»

Содержание SUN2000-33KTL



































































































Отзывы:

Нет отзывов

Похожие инструкции для SUN2000-33KTL

Бренд: ICP DAS USA Страницы: 4

Бренд: Kramer Страницы: 14

Бренд: Microchip Technology Страницы: 56

Бренд: Vanco Страницы: 16

Бренд: VXI Страницы: 57

Бренд: W&T Страницы: 12

Бренд: BSPH Страницы: 36

Бренд: Aspar Страницы: 14

Бренд: Waversasystems Страницы: 15

EZWALL-pro 3x3 v3

Бренд: SmartAVI Страницы: 14

Бренд: Wentronic Страницы: 4

Бренд: CyberPower Страницы: 1

Бренд: Brunner Страницы: 8

Бренд: Metra Electronics Страницы: 3

Бренд: Generac Power Systems Страницы: 4

Бренд: Linear Technology Страницы: 6

Бренд: Hall Research Technologies Страницы: 24

Бренд: JDS Labs Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды