manualshive.com logo in svg

Huawei SUN2000-175KTL-H0, Руководство пользователя, Страница: 84 / 94

Поделиться
Скачать
Huawei SUN2000-175KTL-H0 Скачать руководство пользователя страница 84

SUN2000-(175KTL-H0, 185KTL-INH0, 185KTL-H1) 
User Manual 

8 Maintenance 

 

Issue 02 (2019-06-05) 

Copyright © Huawei Technologies Co., Ltd. 

78 

 

Alarm 
ID 

Alarm 
Name 

Alarm 
Severit
y 

Cause 

Troubleshooting Suggestions 

2061 

Abnorma
l 
Groundin
g 

Major 

1.

 

The PE cable of the inverter is not 
connected. 

2.

 

The inverter output side does not 
connect to an isolation transformer 
when the PV string output is 
grounded. 

1.

 

Check that the PE cable of the 
inverter is connected properly. 

2.

 

If the PV string output is 
grounded, check that the 
inverter output side connects to 
an isolation transformer. 

2062 

Low 
Insulatio
n 
Resistanc
e 

Major 

1.

 

The PV string is short-circuited to 
the PE cable. 

2.

 

The PV string has been in a moist 
environment for a long time and the 
circuit is not well insulated to 
ground. 

1.

 

Check the impedance of the 
PV string to PE. If a short 
circuit occurs, rectify it. 

2.

 

Check that the ground cable of 
the inverter is correctly 
connected. 

3.

 

If you are sure that the 
impedance is less than the 
default value in a cloudy or 
rainy environment, reset 

Insulation resistance 
protection

. 

2063 

Cabinet 
Overtem
perature 

Major 

1.

 

The inverter is installed in a place 
with poor ventilation. 

2.

 

The ambient temperature is too 
high. 

3.

 

The inverter is not working 
properly. 

1.

 

Check the ventilation and 
whether the ambient 
temperature of the inverter 
exceeds the upper limit. If the 
ventilation is poor or the 
ambient temperature is too 
high, improve ventilation. 

2.

 

If both the ventilation and 
ambient temperature meet 
requirements yet the fault 
persists, contact your dealer or 
Huawei technical support. 

2064 

Device 
Fault 

Major 

An unrecoverable fault has occurred 
on a circuit inside the inverter. 

Turn off the AC output switch and 
DC input switch, and then turn 
them on after 15 minutes. If the 
fault persists, contact your dealer 
or Huawei technical support. 

2065 

Upgrade 
Failed or 
Software 
Version 
Unmatch 

Minor 

The upgrade does not complete 
normally. 

1.

 

Perform an upgrade again. 

2.

 

If the upgrade fails several 
times, contact your dealer. 

2066 

License 
Expired 

Warning 

1.

 

The privilege license has entered 
the grace period. 

2.

 

The privilege feature will be invalid 
soon. 

1.

 

Apply for a new license. 

2.

 

Load a new license. 

Содержание SUN2000-175KTL-H0































































































Отзывы:

Нет отзывов