Huawei RRU5303 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 135

background image

RRU5303
Installation Guide

3 Information About the Installation

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

19



The IFS06 supports at least three RRUs when the ambient temperature is higher than or
equal to the lowest operating temperature of the RRUs and at least 5°C (41°F) lower than
the highest operating temperature of the RRUs. The IFS06 supports a maximum of six
RRUs when the ambient temperature is higher than or equal to the lowest operating
temperature of the RRUs and at least 10°C (50°F) lower than the highest operating
temperature of the RRUs.

For details about the operating temperature of the RRUs, see section "Technical Specifications of RRUs"
in

Base Station Technical Description

.

RRUs cannot be stacked when the RRUs are installed on an IFS06, as shown in Figure 3-18.

Figure 3-18

Correct installation of RRUs installed on an IFS06

Figure 3-19 and Figure 3-20 show RRUs installed on an IFS06.

«
...
25
26
27
28
29
...
»

Содержание RRU5303








































































































































Отзывы:

Нет отзывов

Похожие инструкции для RRU5303

Бренд: Valve Concepts Страницы: 16

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

Бренд: K&K Страницы: 6

1E0671-1 MCR2.9

Бренд: Haberl Electronic Страницы: 9

Бренд: J+J Страницы: 2

Бренд: National Instruments Страницы: 17

Бренд: Davey Страницы: 12

CWDM-CR-B Series

Бренд: Lantronix Страницы: 19

Бренд: Netafim Страницы: 4

Бренд: TREND Страницы: 12

Бренд: Sartorius Страницы: 165

Бренд: Contemporary Research Страницы: 22

Бренд: Bard Страницы: 102

Бренд: Vestil Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды