manualshive.com logo in svg

Huawei RRU3262, Руководство по установке, Страница: 73 / 130

Поделиться
Скачать
Huawei RRU3262 Скачать руководство пользователя страница 73

NOTICE

l

Do not stand an RRU upright because the RF ports cannot support the weight of the RRU.

l

Place a foam pad or cardboard under an RRU to protect the RRU housing from damage
during the installation.

Context

Figure 8-22

 shows the top view of an RRU installed on U-steel.

NOTICE

When the width of the narrower edges of the U-steel is less than 40 mm (1.57 in.), only the a
and b modes are supported.

Figure 8-22

 Top view of an RRU

(1) U-steel

 

Procedure

Step 1

Determine a position for installing the mounting brackets.

l

If the RRU is installed on a tower, determine a position for installing the mounting brackets
according to the instructions in 

3.5.1 Clearance for a Single RRU

.

l

If the RRU is installed on the ground, determine a position for installing the mounting
brackets according to the instructions in 

Figure 8-23

.

RRU3262
Installation Guide

8 Installing the RRU

Issue 01 (2014-11-20)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

65

Содержание RRU3262



































































































































Отзывы:

Нет отзывов