Huawei RRU3262 Скачать руководство пользователя страница 74

Страница: 74 / 130

Figure 8-23

Distance between the mounting brackets and the ground

NOTE

As shown in the figure above, it is recommended that the mounting kits be installed at a position
1200 mm (47.24 in.) to 1600 mm (59.06 in.) high above the ground. If the space is insufficient, only
the

3.5 Installation Clearance Requirements of an RRU

needs to be provided.

Step 2

Install the RRU mounting brackets, as shown in

Figure 8-24

Installing the RRU mounting brackets

NOTE

Ensure that the arrows on the mounting brackets are pointing up.

Adjust the position of the nut and remove the square-neck bolt at the open end from the
slot on the auxiliary bracket.

Slide the mounting brackets onto the U-steel horizontally and insert the square-neck bolt
into the slot.

RRU3262
Installation Guide

8 Installing the RRU

Issue 01 (2014-11-20)

Huawei Proprietary and Confidential

Содержание RRU3262



































































































































Результаты поиска

Содержание RRU3262

Отзывы:

Huawei RRU3262, Руководство по установке, Страница: 74 / 130

Результаты поиска

Содержание RRU3262

Отзывы: