Huawei RRU3262 Скачать руководство пользователя страница 18

Страница: 18 / 130

Item

Silkscreen

Remarks

ANT_TX/RXB

TX/RX port B, supporting RET signal
transmission

ANT_RXC

TX/RX port C

ANT_RXD

TX/RX port D

EXT_ALM

Alarm monitoring port used for monitoring
one RS485 signal and two dry contact signals

RET

Communication port for the RET antenna,
supporting RET signal transmission

(3) Indicator

RUN

For details, see

3.3 RRU Indicators

ALM

ACT

VSWR

CPRI0

CPRI1

NOTE

The port for transmitting RET signals is determined by the software.

Connect the

CPRI0

port to the BBU by default in the single-mode scenario.

3.3 RRU Indicators

This section describes six indicators on an RRU. They indicate the running status of the RRU.

For detailed positions of RRU indicators, see

3.2 RRU Ports

Table 3-2

describes RRU indicators.

Table 3-2

RRU Indicators

Indicator

Color

Status

Meaning

RUN

Green

Steady on

The power input is available, but the board is
faulty.

Steady off

No power input is available or the board is
faulty.

Blinking (on for
1s and off for 1s)

The board is running properly.

RRU3262
Installation Guide

3 Information About the Installation

Issue 01 (2014-11-20)

Huawei Proprietary and Confidential

Содержание RRU3262



































































































































Результаты поиска

Содержание RRU3262

Отзывы:

Huawei RRU3262, Руководство по установке, Страница: 18 / 130

Результаты поиска

Содержание RRU3262

Отзывы: