Huawei RRU3201 Скачать руководство пользователя страница 79

Страница: 79 / 96

Add an OT terminal to each end of the cable by referring to Assembling the OT Terminal
and the Power Cable.

Step 2

Install the RRU PGND cable.

Connect the M6 OT terminal at one end of the PGND cable to the ground terminal at the RRU
bottom and the M8 OT terminal at the other end to the external ground bar, as shown in

Figure

8-6

Figure 8-6

Installing an RRU PGND cable

NOTE

Crimp OT terminals in correct positions, as shown in

Figure 8-7

Correct position of an OT terminal

Step 3

Label the installed cable by referring to Attaching a Cable-Tying Label.

----End

8.6 Installing an RRU RF Jumper

This section describes the procedure for installing an RRU RF jumper.

RRU3201
Installation Guide

8 Installing RRU Cables

Issue 06 (2012-04-16)

Huawei Proprietary and Confidential

Содержание RRU3201

































































































Результаты поиска

Содержание RRU3201

Отзывы:

Похожие инструкции для RRU3201

Бренды по названию

Популярные бренды

Huawei RRU3201, Руководство по установке

Результаты поиска

Содержание RRU3201

Отзывы:

Похожие инструкции для RRU3201

Бренды по названию

Популярные бренды