Huawei PowerCube 5000 Скачать руководство пользователя страница 43

Страница: 43 / 103

PowerCube 5000 (SUN2000-150KTL-S0)
Installation Guide

4 Installing Components

Issue 03 (2020-04-10)

Figure 4-5

Installing a GIM01C

----End

4.6 Installing an iBOX

Prerequisites



There should be no other wireless devices such as ZigBee, Bluetooth, WiFi, or wireless base station
devices in the battery room.



The iBOX should be no more than 10 m away from the farthest end of the battery rack.



The iBOX needs to be installed above one end of the battery rack.



There should be no obstructions higher than the battery rack between the iBOX and iBAT.



At least one side should be visible between the iBOX and the battery rack.



Before attaching the iBOX fastener, ensure that the installation surface is smooth and dustless.



It is recommended that the iBOX be installed more than 1 m above the floor. Signals will be weak if
it is installed at a lower position.



To avoid signal shielding, do not install the iBOX at a position with metal walls around it.



The iBOX antenna should be perpendicular to the floor.



Clearance should be kept around the antenna.

Procedure

Step 1

Connect the antenna provided with the iBOX to the RF_Z port on the iBOX.

Step 2

Attach the fastener to the wall.

Step 3

Clamp the iBOX to the fastener.

Содержание PowerCube 5000








































































































Результаты поиска

Содержание PowerCube 5000

Отзывы:

Huawei PowerCube 5000, Руководство по установке, Страница: 43 / 103

Результаты поиска

Содержание PowerCube 5000

Отзывы: