Huawei NetCol5000-C030H90D0 страница 74 Скачать руководство пользователя

Страница: 74 / 206

Figure 3-47 Connecting power cables (NetCol5000-C030/C032)

1. Remove screws from both ends of the clip to remove it.
2. Connect the cables with crimped terminals to the L, N, and PE.

NO TE

NetCol5000-C065 uses a common screwdriver to secure the cables, NetCol5000-C030/

C032 uses a 100-120 mm screwdriver to secure the cables.

3. Place the connected power cables vertically, use the clip to secure them in a

proper position, and use screws to secure the clip.

4. Fasten the power cable to the vertical pillar by cable ties every 150 mm to

200 mm.

Step 4 Use a multimeter to check for a short circuit between L and N of AC1 and AC2.

Use a multimeter to check for a short circuit between L, N, and PE.
●

If there is a short circuit, remove the cable and reconnect it using the method

described in

Step 3.2

. After verifying the connection, perform

Step 5

●

If there is no short circuit, perform

Step 5

Step 5 Check that the cable connections are secure.

●

If the cable connections are loose, fasten the connections.

●

If the cable connections are secure, the connection is complete.

Step 6 Reinstall the cover of the electric control box.

----End

3.12.4 Teamwork Networking and Monitoring

3.12.4.1 Main Control Board Ports

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

3 Installation

Issue 03 (2020-08-30)

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030H90D0, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды