Huawei NetCol5000-C030H90D0 Скачать руководство пользователя страница 68

Страница: 68 / 206

Step 4 After the leakage test has been performed and gas has drained, re-wrap the

needle valve with thermal insulation foam.

----End

Exception Handling

●

If the pressure decreases, find out and repair the leakage point by using soap

bubbles.

●

If the pressure is preserved properly, exhaust nitrogen and wrap pipes and

joints with thermal insulation foams.

----End

3.10 Injecting Water to Expel Gas

Prerequisites

●

Nitrogen must be expelled before injecting water.

●

To avoid blockage of the heat exchanger in the smart cooling product due to

foreign matter from the main pipe during the construction, you are advised to

clean the main pipe before water is supplied to the smart cooling product.

Turn off the isolation valves on the water inlet and outlet pipes before the

cleaning and turn them on afterwards.

Procedure

Step 1 Ensure that the needle valve and exhaust valve on the pipe are closed and the

chilled water valve is in the 100% state, as shown in

Figure 3-39

Figure 3-39 Adjusting the chilled water valve

Step 2 Open the main water inlet valve.
Step 3 Gradually open the exhaust valve, as shown in

Figure 3-15

Figure 3-16

. Air and

chilled water flow out of the exhaust hose together.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

3 Installation

Issue 03 (2020-08-30)

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030H90D0, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Бренды по названию

Популярные бренды