Huawei ME936 Скачать руководство пользователя

Страница: 35 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Description of the Application Interfaces

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Figure 3-22

Connections of the SIM_DET pin

CD is a pin detecting USIM card in the SIM socket, normally, there will be a detect pin
in the SIM Socket.



The normal short SIM connector should be employed. The logic of SIM_DET pin is
shown as in Figure 3-23 . High represents that SIM is inserted; Low represents
that SIM is removed.



When SIM is inserted (hot), SIM_DET pin will change from Low to High;



When SIM is removed (hot), SIM_DET pin will change from High to Low.



ME936 will detect the rising or falling edge of SIM_DET to react the hot swap.

Figure 3-23

The logic of SIM_DET

Modem
Processor

SIM Connector Switch

SIM installed=
Not Connected

SIM not
installed=
GND

WWAN Module

SIM_DET

1.8V

Содержание ME936


















































































Результаты поиска

Содержание ME936

Отзывы:

Похожие инструкции для ME936

Бренды по названию

Популярные бренды

Huawei ME936, Руководство по оборудованию

Результаты поиска

Содержание ME936

Отзывы:

Похожие инструкции для ME936

Бренды по названию

Популярные бренды