Huawei Iris Hellas SUN2000 Series Скачать руководство пользователя страница 91

Страница: 91 / 123

CA UTION

● When a solar inverter is faulty, try to avoid standing in front of the solar

inverter.

● Do not operate the DC switch on the solar inverter before you finish

Step 3

Step 5

● If the AC switch between the solar inverter and the power grid has

automatically disconnected, do not turn on the switch before the fault is

rectified.

● Before power-off for troubleshooting, do not touch the energized components

of the solar inverter. Otherwise, electric shocks or arcing may occur.

Procedure

Step 1

Wear proper personal protective equipment (PPE).

Step 2

If the solar inverter is not shut down due to a fault, send a shutdown command

on the SUN2000 app, SmartLogger, or management system. If the solar inverter

has shut down due to a fault, go to the next step.

Step 3

Turn off the AC switch between the solar inverter and the power grid.

Step 4

Measure the DC current of each PV input string using a clamp meter that is set to

the DC position.
●

If the current is less than or equal to 0.5 A, go to the next step.

●

If the current is higher than 0.5 A, wait until the solar irradiance decreases

and the PV string current decreases below 0.5 A at night, and then go to the

next step.

Step 5

Open the maintenance compartment door, install a support bar, and use a

multimeter to measure the voltage between the AC terminal block and the

ground. Ensure that the AC side of the solar inverter is disconnected.

Step 6

Turn off all DC input switches of the solar inverter.

Figure 8-1

Power-off for maintenance

SUN2000-(175KTL-H0, 185KTL-INH0, 185KTL-H1

User Manual

8 Maintenance

Issue 05 (2020-08-30)

Содержание Iris Hellas SUN2000 Series




























































































































Результаты поиска

Содержание Iris Hellas SUN2000 Series

Отзывы:

Похожие инструкции для Iris Hellas SUN2000 Series

Бренды по названию

Популярные бренды

Huawei Iris Hellas SUN2000 Series, Руководство пользователя

Результаты поиска

Содержание Iris Hellas SUN2000 Series

Отзывы:

Похожие инструкции для Iris Hellas SUN2000 Series

Бренды по названию

Популярные бренды