A Install the SD card/ 安装 SD 卡
Install the Device/ 设备安装
1
3
Connect the cables to the tails of the camera, perform insulation
operations on the cables (see
Connect Cables
), and put the cables
through the cable entry on the wall(To route cables from the side, use a
Phillips screwdriver to open the cable outlet on the side). Use the torque
of 5 to 7 kgf.cm to fasten the tapping screws.
将线缆与摄像机的尾线连接，对线缆进行绝缘处理（参见“连接线缆”），然
后塞入墙壁出线孔（如果要从侧方走线，请用十字螺丝刀打开图中标红的侧方
出线口出线）。使用 5~7Kgf.cm 的扭矩拧紧自攻螺钉。
B Surface-Mount/ 吸顶安装
2
Use a Phillips screwdriver to remove the transparent cover, lightly press
the inner cover without blocking the two holes, and remove the inner
cover.
使用十字螺丝刀卸下透明罩，然后双指轻压内罩非固定卡扣位置，卸下内罩。
Use a
Phillips screwdriver
to remove the
transparent cover
, install the SD
card.
使用十字螺丝刀将透明罩卸下，插入 SD 卡。
4
This camera uses the tri-axis design, allowing horizontal rotation of
0~356° , vertical rotation of 0~90° , and chipset rotation of 0~356° to
satisfy different installation angle. Use a Phillips screwdriver to loosen
screws on the chipset, and adjust the surveillance angle. After the
adjustment is complete, tighten the screws on the chipset. After the
adjustment is complete, tighten the screws on the chipset.
该款摄像机为三轴工艺设计，水平方向可转动 0~356° ，垂直方向可转动
0~90° ，机芯可以转动 0~356° ，适应不同角度的安装。使用十字螺丝刀将
固定机芯的螺丝拧松，调整监控角度，调整完毕后，拧紧固定机芯的螺丝。
5
Lightly press the inner cover, and fix it to the chipset. Then align the
transparent cover with the base through the tapped holes, close the
transparent cover, and use a Phillips screwdriver to tighten the screws.
双指轻压内罩，将内罩卡槽对准卡扣，固定内罩，然后将透明罩和底座的螺孔
位置对齐，合上透明罩并使用十字螺丝刀拧紧螺钉。
NOTE/ 说明
The indoor direct wall-mount method is similar to the surface-mount
installation. Install the camera on the wall by referring to
B Surface-Mount
.
When a camera is installed horizontally by default, the surveillance image
is displayed horizontally. Carefully adjust the surveillance angle when
installing the camera to prevent the reverse image display.
室内直接壁装方法与吸顶安装类似，请参见“B 吸顶安装”，将摄像机安装在墙壁上。
摄像机默认水平安装时，监控画面为水平显示。安装过程中，请注意调整监控角度，
避免安装完成后视频画面翻转。
Paste the drilling sticker in the camera installation position and ensure
that the center of the sticker overlaps the center of the cable outlet
on the wall. Obtain a drill bit with a 5 mm diameter and drill four 35
mm holes in the specified positions marked by the stickers. Use a claw
hammer to install an expansion bolt into the hole.
将安装定位贴纸贴在摄像机安装位置，贴纸中心请对准墙壁出线孔。依照贴纸
上的标注，选择直径为 5mm 的钻头，钻取深约 35mm 的导孔，并使用羊角
锤将膨胀螺栓打入钻好的孔内。
The cable outlet
on the side
侧方出线口
