Huawei IPC6125-WDL-FA Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 202

background image

9.1 Configuring the Intrusion Detection Function

The intrusion detection function checks whether an object enters a sensitive area (a key
surveillance area for which behavior analysis rules have been configured). The system
generates an alarm when an object enters a sensitive area.

Prerequisites

Predefined sensitive areas for behavior analysis can be displayed on live video images only
when

Video stream type

is set to

Hybrid stream

. To set

Video stream type

, choose

Settings

>

System Configuration

>

Local Parameters

.

Context

l

Ensure that the camera lens is not blocked by objects, for example, leaves and columns,
to effectively and continuously track the object. Do not directly place the camera lens
opposite to a light source, water surface, or reflection plane, to prevent interference or
false alarms.

l

Before configuring the intelligent analysis function, ensure that the camera lens is
focused accurately, video images are clear, and light conditions are proper. If the
illuminance is lower than 20 lux, or video images are not clear with much noise, set
artificial light sources for light compensation to ensure even and proper light.

l

During the intelligent analysis test, the angle between the horizontal view angle of the
camera (that is, the optic normal of the camera lens) and the level ground or plane of the
monitoring object (for example, wall), must be greater than 15 degrees (reference: 30
degrees to 45 degrees) to ensure that the top of the monitoring object is covered.

l

The camera installation height must be determined based on the site requirements
(reference: 5 m to 6 m for tilted installation and 3 m to 5 m for vertical installation). A
proper installation height can ensure that the object size displayed in video images is
greater than the minimum object size and less than the maximum object size. It is
recommended that the object size be 1/8 to 1/3 of the image size.

l

It is recommended that

Frame rate

be set to

10

or higher on

Settings

>

Channel

Configuration

>

Video&Stream Parameters

to prevent impact on the behavior

analysis effect, for example, the object box is lost, the object box does not match the
object size, or all object boxes are displayed with delay.

Procedure

Step 1

Choose

Settings

>

Intelligent Analysis

>

Behavior Analysis Parameters

.

The

Behavior Analysis Parameters

page is displayed, as shown in

IPC6125-WDL-FA
Configuration Guide

9 Setting Intelligent Analysis Parameters

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

102

«
...
106
107
108
109
110
...
»

Содержание IPC6125-WDL-FA











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IPC6125-WDL-FA

Бренд: Canon Страницы: 212

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 48

EF 100-400mm f/4.5-5.6L IS USM

Бренд: Canon Страницы: 9

EF-M 18-55mm f3.5-5.6 IS STM

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 28

Бренд: Olympus Страницы: 1

PowerShot ELPH 110 HS

Бренд: Canon Страницы: 218

Бренд: Panasonic Страницы: 314

PowerShot ELPH 510 HS

Бренд: Canon Страницы: 212

FE110 - 5 Megapixel Digital Camera

Бренд: Olympus Страницы: 2

Бренд: Olympus Страницы: 75

Бренд: Digisol Страницы: 25

Бренд: Sakar Страницы: 32

ARTCAM-036MI2 Series

Бренд: ARTRAY Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды