Huawei eLTE2.2 eA660 Series Скачать руководство пользователя

Страница: 13 / 51

eLTE2.2 eA660 Series CPE
User Guide

2 Hardware

Issue 01 (2013-10-30)

Huawei Proprietary and Confidential

Name

Description

antenna installation

。

Indicators of the eA660 are below the SIM card maintenance window and are used to indicate
the running status of the eA660.

The four indicators from top to bottom are

POWER

WLINK

RSSI

, and

HEAT

, as shown

Figure 2-3

Figure 2-3

Indicators of the eA660

Table 2-2

describes the indicators of the eA660.

Table 2-2

Indicators of the eA660

Identifier

Status

Description

POWER

The power supply is normal.

Off

No power is supplied.

WLINK

Steady on

The eA660 is successfully registered
to the network.

Blink per 1000 ms

The product fails to register to the
network.

RSSI

NOTE

The blink frequency

Steady on

The signal strength ranges from –40
dBm to –60 dBm.

Blink per 500 ms

The signal strength ranges from –60

Содержание eLTE2.2 eA660 Series




















































Результаты поиска

Содержание eLTE2.2 eA660 Series

Отзывы:

Похожие инструкции для eLTE2.2 eA660 Series

Бренды по названию

Популярные бренды

Huawei eLTE2.2 eA660 Series, Руководство пользователя

Результаты поиска

Содержание eLTE2.2 eA660 Series

Отзывы:

Похожие инструкции для eLTE2.2 eA660 Series

Бренды по названию

Популярные бренды