Huawei E8000E-X16 Скачать руководство пользователя | Manualshive

Страница: 29 / 182

background image

Table 2-10

Technical parameters of the fan module

Item

Technical Parameter

Dimensions (Width x Depth x Height)

210.4 mm x 100 mm x 243.7 mm

Weight

3.4 kg

Power consumption (typical value)

30 W

Maximum noise

74 dB

Fan Speed Adjustment

When the system is fully configured, temperatures reported by the temperature sensors on the
LPUs, SFUs, and MPUs serve as the basis for fan speed adjustment. General principles are listed
below:

When the ambient temperature is between -5°C and 27°C, fans rotate at a low speed (2200/min).
When the ambient temperature is above 50°C, fans rotate at a high speed (5900/min). When the
ambient temperature is between 27°C and 50°C, fan speed increases or decreases in tandem with
temperature movements.

l

When the ambient temperature is 27°C or below, fans rotate at a fixed low speed, which
meets the ETSI noise requirement and the heat dissipation requirement.

l

When the ambient temperature is between 27°C and 50°C, the speed of fans is adjusted
smoothly in linear mode, and there are slight changes in noise levels.

2.7.3 Air Filter

This section describes the appearance of the air filter.

The E8000E-X16 draws in air from the front and exhausts air from the rear. The two air filters
on the upper and lower chassis are identical. To maximize air intake, the filters are fully
perforated. Air filters are fixed to the chassis by fasteners to facilitate filter removal and
replacement.

Figure 2-12

shows the appearance of an air filter.

Figure 2-12

Air filter

The air channel in the SFU area is located on the left of the chassis. The air filter uses front
access. The depth of the air filter is the same as that of an SFU and the height of the air filter is
four times the width of an SFU as shown in

Figure 2-13

.

HUAWEI Eudemon8000E Firewall
Hardware Description

2 E8000E-X16 Chassis Overview

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

19

«
...
27
28
29
30
31
...
»

Содержание E8000E-X16























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E8000E-X16

SecPath F1000-AI-X0

Бренд: H3C Страницы: 73

ProSafe FVS318v3

Бренд: NETGEAR Страницы: 20

Check Point IP2450

Бренд: Nokia Страницы: 136

Бренд: BeyondTrust Страницы: 18

3C16111 - SuperStack 3 Firewall Web Site Filter

Бренд: 3Com Страницы: 214

Бренд: Celestix Страницы: 70

STM150 - ProSecure Web And Email Threat Management Appliance

Бренд: NETGEAR Страницы: 2

STM150 - ProSecure Web And Email Threat Management Appliance

Бренд: NETGEAR Страницы: 248

Бренд: Barracuda Networks Страницы: 5

Бренд: BESTEK Страницы: 12

Бренд: BESTEK Страницы: 47

Бренд: BESTEK Страницы: 67

Бренд: BESTEK Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды