Huawei BTS3900 V100R003 Скачать руководство пользователя

Страница: 176 / 264

Item

Cable

One End

The Other End

Connector

Installatio
n Position

Connector

Installatio
n Position

5.8.5 Fan
Box
Cascade
Signal
Cable

RJ-45
connector

COM OUT

port on the
upper-level
fan box

NOTE

Upper-level
fan box: the
fan box
directly
connected to
the BBU.

RJ-45
connector

COM IN

port on the
lower-level
fan box

NOTE

Lower-level
fan box: the
fan box
connected to
the upper-
level fan box
and then to
the BBU.

5.8.10
Signal
Cable for
the ELU

RJ-45
connector

ELU

RJ-45
connector

SENSOR

the fan box

RF Cables

Table 5-5

lists the RF cables.

Table 5-5

RF Cables

Item

Cable

One End

The Other End

Connector

Installatio
n Position

Connector

Installation
Position

Cables to be
installed on
site

5.9.1 RF
Jumper

DIN elbow
male
connector

RF ports on
the RFU

DIN straight
male
connector

Antenna
system

Cables
installed
before
delivery

5.9.2 Inter-
RFU RF
Signal
Cable

QMA elbow
male
connector

RX OUT

port on one
RFU panel

QMA elbow
male
connector

RX IN

port

on another
RFU panel

5.2 BTS3900 Cable Connections

The cable connections in the BTS3900 vary according to the power supply scenarios and
configurations related to the cabinet, transmission system, CPRI port, and RF.

5.2.1 Power Cable Connections

This section describes the power cable connections of the BTS3900 cabinet.

5 BTS3900 Cables

BTS3900

Hardware Description

5-8

Huawei Proprietary and Confidential

Issue 04 (2011-02-15)

Содержание BTS3900 V100R003









































































































































































































































































Результаты поиска

Содержание BTS3900 V100R003

Отзывы:

Похожие инструкции для BTS3900 V100R003

Бренды по названию

Популярные бренды

Huawei BTS3900 V100R003, Описание аппаратуры

Результаты поиска

Содержание BTS3900 V100R003

Отзывы:

Похожие инструкции для BTS3900 V100R003

Бренды по названию

Популярные бренды