Huawei AISU Скачать руководство пользователя страница 43

Страница: 43 / 47

AISU

User Manual

6 Maintenance Guide

Issue 02 (2017-06-12)

Huawei Proprietary and Confidential

Step 5

Replace the AISU.

After replacing the AISU, remove the abnormal AISU, and scan, add, and configure the new
AISU. After 5 minutes, check whether the alarm is cleared.



If the alarm is cleared, no further action is required.



If the alarm persists, contact Huawei technical support engineers.

After replacing the AISU, reconfigure the AISU by referring to section 5 "

Configuration Guide

----End

Hardware Fault

Context

If the AISU is faulty, ALD Hardware Fault is reported.

Table 6-4 describes the hardware fault symptom.

Table 6-4

Symptom

Symptom

Impact on the

System

Severity

Probable Cause

If any component in
the AISU is faulty,
ALD Hardware
Fault is reported.

The downtilt of the
RET antenna fails to
be regulated.

Minor

The AISU board is
faulty or damaged.

Figure 6-2 shows the detailed information about ALD Hardware Fault.

Figure 6-2

ALD Hardware Fault

Содержание AISU
















































Результаты поиска

Содержание AISU

Отзывы:

Huawei AISU, Руководство пользователя, Страница: 43 / 47

Результаты поиска

Содержание AISU

Отзывы: