manualshive.com logo in svg

Huawei 9000 VCT V100R011, Руководство администратора, Страница: 171 / 204

Поделиться
Скачать
Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 171

Figure 11-4

 shows the diagnostics of three modules, including the audio module, video module,

and network send/receive module.

Normal audio signal streams are as follows:

l

Local microphone → 1 → 5 → communication network → 6 → 7 → remote speaker

l

Local speaker ← 2 ← 5 ← communication network ← 6 ← 8 ← remote microphone

Normal video signal streams are as follows:

l

Local camera → 3 → 5 → communication network → 6 → 9 → remote display

l

Local display ← 4 ← 5 ← communication network ← 6 ← 10 ← remote camera

Sound and Color Bar Tests

Table 11-3

 describes sound and color bar tests.

Table 11-3

 Sound and color bar tests

Test

Item to Be Tested/Objective

Signal Stream

Sound test

2 audio output

2 → speaker

Color bar test

4 video output

4 → display

 

l

To perform a sound test, choose 

Diagnostics

 > 

Sound & Color Bar Test

 > 

Sound Test

.

The terminal plays an embedded tone to test the audio output quality.

l

To perform a color bar test, and then choose 

Diagnostics

 > 

Sound & Color Bar Test

 >

Color Bar Test

. The terminal displays 6 color bars on the display to test the color output

quality.

Loopback Tests

The terminal can transmit audio or video data on a channel to simulate the actual application
and test whether the output is satisfactory. You can perform a local loopback test to check the
local network connection or a remote loopback test to check the remote network connection. If
a remote loopback test is performed, data is transmitted from the local site to a remote site, and
then back to the local site. 

Table 11-4

shows the available loopback tests on the terminal and

their objectives.

WARNING

l

To enable the terminal to communicate with other terminals properly, the loopback test
must be stopped.

l

A remote video loopback test cannot be performed during a dual-stream conference.

HUAWEI 9000 HD Video Terminal
Administrator Guide

11 Maintenance and Troubleshooting

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

159

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов