Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 172

Страница: 172 / 204

Table 11-4

Loopback tests

Test

Item to Be Tested/
Objective

Signal Stream

Local audio
loopback

Local audio module

Microphone → 1 → 2 → speaker

Local video
loopback

Local video module

Camera → 3 → 4 → display

Local digital
loopback

Local audio-visual
modules

The terminal performs local audio and
video loopback tests simultaneously.

Remote audio
loopback

Remote audio module

Network transmission

Microphone → 1 → 5 → 6 → 7 → 8 → 6
→ 5 → 2 → speaker

Remote video
loopback

Remote video module

Network transmission

Camera → 3 → 5 → 6 → 9 → 10 → 6 →
5 → 4 → display

Remote digital
loopback

Remote audio-visual
modules

Network transmission

The terminal performs remote audio and
video loopback tests simultaneously.

Network Test

Table 11-5

Network test

Test

Item to Be Tested/
Objective

Signal Stream

Network test

IP access

Terminal → LAN or public network

Before a test, ensure that the terminal is connected to an IP network properly, the indicator of
the LAN network interface turns green, and the IP parameters are set correctly.

IP address

, enter an IP address. Ensure that the IP address entered and the IP address

of the terminal are in different network segments. Select

Start

. If the test is passed, it

indicates that the gateway settings and the IP address of the terminal are correct.

If the terminal exists in a private network, enter an IP address in a public network in

address

, and then select

Start

. If the test is passed, it indicates that the gateway settings,

the NAT address, and the IP address of the terminal are correct.

Remote Control Test

Test keys on the remote control to check whether they function properly. If some of the keys

are checked, the

Remote Control Test

screen can be exited by pressing and holding the

the remote control.

After all keys have been tested, the

Remote Control Test

screen is exited automatically.

HUAWEI 9000 HD Video Terminal
Administrator Guide

11 Maintenance and Troubleshooting

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

160

Содержание 9000 VCT V100R011













































































































































































































Результаты поиска

Содержание 9000 VCT V100R011

Отзывы:

Huawei 9000 VCT V100R011, Руководство администратора, Страница: 172 / 204

Результаты поиска

Содержание 9000 VCT V100R011

Отзывы: