manualshive.com logo in svg

Huawei 3900 Series, Руководство по вводу в эксплуатацию

GE 3900 Series - набор продукции с полным комплектом руководств по использованию - найдите их в режиме онлайн и загрузите бесплатно на manualshive.com. Откройте мир новых возможностей с GE 3900 Series Product Manual.

Поделиться
Скачать
background image

Procedure

Step 1

Create an MBTS commissioning task by referring to 

4.3 Creating an MBTS Commissioning

Task

.

Step 2

Perform operations according to whether 

Intervene Transmission

 is selected when a

commissioning task is created.

If...

Then...

Intervene Transmission

 is selected when a

commissioning task is created,

Go to 

Step 3

.

Intervene Transmission

 is not selected

when a commissioning task is created,

Go to 

Step 4

.

 

Step 3

Check the transmission state and rectify faults (if any) manually. For details, see 

4.4 Manually

Intervening the MBTS Transmission Detection

.

Step 4

The M2000 automatically commissions the MBTS. For details on the commissioning process,
see 

4.5 Automatic Commissioning of the MBTS on the M2000

. During the commissioning

process, view the commissioning progress, rectify faults (if any) to ensure that the
commissioning is successful. For details, see 

4.6 Monitoring the MBTS Commissioning

.

Step 5

After the MBTS service verification passes, the commissioning status is displayed 

. Check

that the MBTS commissioning is completed. For details, see 

4.7 Confirming the Completion

of MBTS Commissioning

.

Step 6

Obtain the MBTS commissioning report. For details, see 

4.8 Obtaining the MBTS

Commissioning Report

.

----End

4.2 Preparing for MBTS Commissioning

This section describes how to prepare for MBTS commissioning.

Prepare for MBTS commissioning by referring to 

Table 4-1

.

Table 4-1

 Preparing for MBTS commissioning (in case of new deployment of both GBTS and

NodeB)

Step

Operation

1

Check that the MBTS hardware, such as the cabinets, cables, antenna system, and
auxiliary devices, is installed and passes the installation check. In addition, check
that the MBTS is powered on and passes the power-on check.

2

Check that the controller hardware is installed and commissioned successfully and
the controller runs normally. In addition, check that the negotiation data of the
base station to be commissioned is configured and recorded.

3

Check that the M2000 is commissioned, that the M2000 is connected to the
corresponding controller, and that the configuration synchronization is completed.

4 Commissioning the MBTS in GU Mode on the M2000

3900 Series Multi-Mode Base Station

Commissioning Guide

4-4

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

Issue 02 (2010-07-30)

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

Voxx 250-9900 Installation Manual preview
250-9900
Бренд: Voxx Страницы: 7
GE 28310 Setup Manual preview
28310
Бренд: GE Страницы: 2
3Com SuperStack 3 4300 User Manual preview
SuperStack 3 4300
Бренд: 3Com Страницы: 8
3B Medical Lumin LM3000 User Manual preview
Lumin LM3000
Бренд: 3B Medical Страницы: 7
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Бренд: Tesla Страницы: 9
probrake SU10-5 Mounting Instruction preview
SU10-5
Бренд: probrake Страницы: 2
Metra Electronics 99-3030B Installation Instructions Manual preview
99-3030B
Бренд: Metra Electronics Страницы: 12
Halfords Exodus 360 Fitting Instructions preview
Exodus 360
Бренд: Halfords Страницы: 4
ST STEVAL-IOD04KT1 User Manual preview
STEVAL-IOD04KT1
Бренд: ST Страницы: 13
Carinae Sports Speed Sensor User Manual preview
Speed Sensor
Бренд: Carinae Sports Страницы: 22
Elk Products ELK-319WS Quick Start Manual preview
ELK-319WS
Бренд: Elk Products Страницы: 2
Elk ELK-319WS Quick Manual preview
ELK-319WS
Бренд: Elk Страницы: 2
Olympus PT-022 Instruction Manual preview
PT-022
Бренд: Olympus Страницы: 43
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Бренд: Kolpin Outdoors Страницы: 6
Schartec CR 4 Manual preview
CR 4
Бренд: Schartec Страницы: 2
Toro 140-1914 Installation Instructions Manual preview
140-1914
Бренд: Toro Страницы: 8
Camtraptions PIR V3 Manual preview
PIR V3
Бренд: Camtraptions Страницы: 10
LANSING LIGHTING SY01 Quick Start Manual preview
SY01
Бренд: LANSING LIGHTING Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды