Huawei 3900 Series Скачать руководство пользователя страница 143

Страница: 143 / 196

If the VSWR LED
is...

It Indicates That... Then...

OFF

No VSWR alarm is
generated.

Wait till the transmission is available.

Blinking (ON for
0.125s and OFF for
0.125s)

There are alarms on
the ANT_TX/RXA
port and ANT_RXB
port.

Check whether the antenna system is properly
connected to the MRFU or RRU3908.
If the fault persists, record the fault and the
LED status in the

7.10 Data Sheet for

Commissioning

. Then, rectify the fault on the

LMT or M2000.

There is an alarm on
the ANT_TX/RXA
port.

Blinking (ON for 1s
and OFF for 1s)

There is an alarm on
the ANT_RXB port.

----End

6.5 Set the Download Control Right

If the BTS is working in the co-module scenario, the download control right needs to be set. The
system with the download control right upgrades the co-modulated RRU3908/MRFU and the
USCU software during software upgrade.

Prerequisite

M2000 server/terminal is working properly, and M2000 is logged on.

The connection between BTS and M2000 is working properly. If the BTS is GSM BTS,
the connection between the BSC and M2000 needs to work properly.

Procedure

Step 1

Run the corresponding MML command to set the download control right according to the actual
system of BTS, see

Table 6-8

The corresponding MML commands of setting the download control right versus the

BTS Systems

BTS Systems

MML Commands

GSM

SET BTSLOADCTRL

UMTS

SET LOADCTRL

LTE

SET LOADCTRL

----End

3900 Series Multi-Mode Base Station
Commissioning Guide

6 Commissioning the MBTS by Using USB and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

6-25

Содержание 3900 Series





































































































































































































Результаты поиска

Содержание 3900 Series

Отзывы:

Похожие инструкции для 3900 Series

Бренды по названию

Популярные бренды

Huawei 3900 Series, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание 3900 Series

Отзывы:

Похожие инструкции для 3900 Series

Бренды по названию

Популярные бренды