Huawei 3900 Series Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 196

background image

Step 5

Click the

Execute

button. The eNodeB performs the selected tasks from top to bottom. There

is a progress bar under the

Execute

button, indicating the current progress and status of the task.

When the progress bar of each task displays 100%, the upgrade is complete.

CAUTION

If a task fails, the eNodeB stops the task and does not proceed with subsequent tasks. If only the
data configuration file is downloaded and activated during the upgrade, you need to manually
reset the eNodeB after the data configuration file is activated so that the updated data takes effect.
The eNodeB is automatically reset after the eNodeB software is activated. Before the eNodeB
is automatically reset, do not send any reset command to the eNodeB or boards, and do not power
off the eNodeB or remove the boards. If you perform any of the preceding operations before the
eNodeB is automatically reset, the upgrade fails, and the software and files on the boards may
be cleared or damaged.

----End

7.9 Downloading the eNodeB License

By downloading the license to the eNodeB on the LMT, you are authorized to use the eNodeB
software.

Prerequisite

l

The LMT communicates properly with the eNodeB.

l

The license is already obtained.

Procedure

Step 1

Run the

INS LICENSE

command to download and activate the license on the eNodeB.

----End

7.10 Data Sheet for Commissioning

This chapter provides the data sheet that is used to record the process and result of the
commissioning.

7.10.1 Data Sheet for GBTS Commissioning

This section provides the data sheet that is used to record the process and results of the GBTS
commissioning.

7.10.2 Data Sheet for NodeB Commissioning

This section provides the data sheet that is used to record the process and results of the NodeB
commissioning

7.10.3 Data Sheet for eNodeB Commissioning

This section provides the data sheet that is used to record the process and results of the eNodeB
commissioning. The Data Sheet for Commissioning used at different sites may be different. This
table serves as a reference only.

3900 Series Multi-Mode Base Station
Commissioning Guide

7 Commissioning the MBTS by Using Local Maintenance

Terminal and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

7-41

«
...
183
184
185
186
187
...
»

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

Бренд: 3M Страницы: 26

Бренд: T-Tech Страницы: 38

Бренд: 7AMEnfant Страницы: 2

Бренд: Calsense Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Feniex Страницы: 6

Бренд: Fencing SmartBox Страницы: 11

Бренд: Feiyu Страницы: 4

Бренд: FAZUA Страницы: 84

Бренд: GAI-Tronics Страницы: 22

MARTEN-FREE CAR

Бренд: Gardigo Страницы: 36

Бренд: BAFANG Страницы: 12

Бренд: Trailboss Страницы: 5

Бренд: Mazdaspeed Страницы: 8

Бренд: Actia Страницы: 37

Бренд: Kargo Master Страницы: 6

CombiCool CAB-40B

Бренд: Waeco Страницы: 136

Бренд: CASTLECREEK Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды