background image

Huahuan 

                                 

Beijing Huahuan Electronics Co., Ltd.

 

TDMUX-16 User Manual   V1.2

                           

-

1-

 

1.

 

 

 

General 

1.1

 

Overview 

Thank you for selecting the H0FL-ETHMUX V16 E1/T1 over IP/Ethernet 

product designed and made by Beijing Huahuan Electronics Co., Ltd. The product 
can be used to provide E1/T1 communication channels over Ethernet or IP 
networks.  

The H0FL-ETHMUX V16 has many optional parameters, which can be 

modified by the user to suite different application requirements. Please read this 
manual carefully before installing the product.   

It is well known that the E1/T1 signal comes from PCM technology which is 

TDM in nature. It transmits information in a constant bit rate of 
E1_2048kbit/S(T1_

 

1.544Mbit/s)

, TDM technology occupies fixed transmission 

bandwidth, with QoS features suitable for real-time applications such as voice and 
video. The QoS features include short and stable transmission delay, low jitter and 
wander, etc.   

On the other hand, Ethernet is based on statistical multiplexing, transmitting 

and exchanging information in packets. It does not take up a fixed transmission 
bandwidth, which is good for achieving higher bandwidth utilization. But Ethernet 
technology does not provide adequate QoS for real time applications.   

Until recently, voice and data were, and still are to a large extent, transported 

over two separate networks. But the requirement for both types of information to 
be carried over a unified network is growing rapid. Packets over SONET/SDH 
techniques to integrate date into the TDM network have been around for many 
years. But for voice over packet based data networks, most of the efforts are spent 
on creating special equipment that packets voice or video signals, such as VoIP 
techniques. 

However, to take advantage of the data network, it is neither cost effective, 

nor necessary to hastily replace all the TDM based equipment with new packet 
based equipment. The H0FL-ETHMUX V16 can be used to emulate transparent E1 
channels over an Ethernet with adequate QoS, so that most of the existing E1based 
applications can be readily setup over Ethernet LANs and WANs. One particular 
suited application is to build E1 links with low cost wireless LAN bridges, 
replacing much more costly microwave radios.   

H0FL-ETHMUX V16 Features 

z

 

Provide 16 channels of E1/T1 over 1 Ethernet. 

z

 

Provide 5 GE electrical ports and 1 GE optical port, 6 GE ports serve as 

Содержание H0FL-ETHMUX V16
































Отзывы: