lp-606 Rev. 000 Rel. 006 Date 2.19.20
3
Part 1 - General Safety Information
Installer -
Read all instructions in this manual before installing.
Perform steps in the given order.
User
- This manual is for use only by a qualified heating installer
/ service technician. Have this water heater serviced / inspected
annually by a qualified service technician.
Failure to adhere to these guidelines can result in substantial
property damage, severe personal injury, or death.
NOTE:
Obey all local codes. Obtain all applicable permits before
installing the water heater.
NOTE:
Install all system components and piping in such a manner
that does not reduce the performance of any fire rated assembly.
DO NOT USE THIS WATER HEATER IF ANY PART HAS BEEN
SUBMERGED IN WATER.
Immediately call a qualified service
technician. The water heater MUST BE replaced if it has been
submerged. Attempting to operate a water heater that has been
submerged could create numerous harmful conditions, such as
a potential gas leakage causing a fire and/or explosion, or the
release of mold, bacteria, or other harmful particulates into the
air. Operating a previously submerged water heater could result in
property damage, severe personal injury, or death.
NOTE:
Water heater damage due to flood or submersion is
considered an Act of God, and IS NOT covered under product
warranty.
NOTE:
If the solar water heater is exposed to the following, do not
operate. Immediately call a qualified service technician.
1. Fire
2. Damage
3. Submersion in Water
Failure to adhere to these guidelines can result in substantial
property damage, severe personal injury, or death.
Only use this water heater as intended and described in this
installation manual. Any use other than described will void
warranty and may lead to fire, property damage, personal injury,
or death.
Improper installation or use may result in property damage. Such
damages ARE NOT covered by warranty.
UNCRATING THE WATER HEATER
- Any claims for damage or
shortage in shipment must be filed immediately against the
transportation company by the consignee.
ALL PIPING AND PLUMBING CONNECTIONS SHOULD BE MADE
WITH COPPER PIPE ONLY.
No less than ¾” I.D. copper tube of the
type meeting local codes must be used for piping. Pipe runs must
be solidly attached with proper clamping methods. Soldered
A. When Servicing the Solar Water Heater
To avoid electric shock, disconnect electrical supply before performing
maintenance.
To avoid severe burns, allow solar collector and associated equipment
to cool before servicing.
B. Local Installation Regulations
Installation of this solar water heater may be governed by individual
local rules and regulations, which must be observed. Always use
the latest edition of codes. The installation, adjustment, service, and
maintenance of the solar water heater must be done by a licensed
professional who is qualified and experienced in the installation,
service, and maintenance of solar hot water heaters.
C. Chemical Vapor Corrosion
Products to Avoid
Areas Likely to Have
Contaminants
Spray cans containing
fluorocarbons
Dry cleaning / laundry areas
and establishments
Permanent wave solutions
Swimming pools
Chlorinated waxes / cleaners
Metal fabrication plants
Chlorine-based swimming pool
chemicals
Beauty shops
Calcium chloride used for
thawing
Refrigeration repair shops
Sodium chloride used for water
softening
Photo processing plants
Refrigerant leaks
Auto body shops
Paint or varnish removers
Plastic manufacturing plants
Hydrochloric or Muriatic acid
Furniture refinishing areas and
establishments
Cements and glues
New building construction
Antistatic fabric softeners used in
clothes dryers
Remodeling areas
Chlorine-type bleaches, laundry
detergents, and cleaning solvents
Garages and workshops
Adhesives used to fasten building
products
Table 1 - Products and Areas Likely to Have Contaminants
NOTE: DAMAGE TO THE WATER HEATER, COLLECTOR, OR
RELATED COMPONENTS CAUSED BY EXPOSURE TO CORROSIVE
VAPORS IS NOT COVERED BY WARRANTY.
(Refer to the limited
warranty for complete terms and conditions.)
D. Insulation Blankets
For installation of insulation blankets, refer to
Solar Water Heating
System Design and Installation Guidelines, SRCC OG-300
.
NOTE:
System performance and efficiency varies with factors such
as: household hot water load, ambient air temperature, collector/
roof pitch, collector orientation, and seasonal intensity.
Job site conditions will require your installation contractor to supply
some or all of the following:
•
Plumbing connections
•
Piping and insulation
•
Valves between your backup water system and the solar
system
NOTE:
Failure to follow the procedures and instructions in this
manual WILL VOID the warranty.
connections should be secured with 95/5 lead-free solder. Use only
pipe rated for 250
o
F minimum on both the collector return and supply
piping.