HTP Inverarc 200 TLP, Руководство пользователя

Страница: 10 / 14

10
DESCRIPTION OF THE WELDING FUNCTIONS
When you switch the welder on, all of the indicator LEDs will illuminate for approximately two seconds,
and then the multifunction/amperage display (Fig. 2, #8) and the reference LED showing the welding mode
selected (Fig. 2, # 3, #4, or #5) will both blink. Approximately two seconds later, the multifunction/
amperage display (Fig. 2, #8) will show the welding current, which you can adjust as necessary with the
encoder (Fig. 2, #9). The power indicator LED (Fig. 2, #6) remains illuminated while the welder is switched
on.
DESCRIPTIONS OF THE REGULATIONS IN THE VARIOUS WELDING MODES
STICK WELDING (ARC)
1) Press the Select Mode button (Fig. 2, #2) to switch on the Arc Weld Mode LED (Fig. 2, #5).
2) The display (Fig. 2, #8) will blink ARC for approximately two seconds.
3) The Arc Force Indicator LED (Fig. 2, #10) will illuminate.
4) Use the encoder (Fig. 2, #9) to regulate the welding current shown on the display (Fig. 2, #8).
5) You can adjust the Hot Start value by pressing and holding the Function button (Fig. 2, #13) for several
seconds until the display (Fig. 2, #8) shows HS . Once you see HS , let go of the Function button; the HS
should be replaced by a number between 003 and 040. The number displayed refers to the hot start value
as a percentage. For example, if you weld at 100 amps and set the HS to 003, for a short period of time
after you strike an arc, the welding output is raised to 103 amps. Likewise, if you weld at 100 amps and
set the HS to 040, for a short period of time after you strike an arc, the welding output is raised to 140
amps.
6) Pressing the Function button (Fig. 2, #13) once allows you to select the Arc Force value. The display
(Fig. 2, #8) will blink AF , and then you can select the value with the encoder (Fig. 2, #9). The Arc Force
can be varied from 0% to 200% based on the set welding current value.
7) Pressing the Function button (Fig. 2, #13) again activates the pulse frequency mode. The Pulse Function
Indicator LED (Fig. 2, #12) will blink and the display will read P Fr . By turning the encoder (Fig. 2, #9),
you can vary the frequency value from 0.4Hz to 5Hz. The factory set the base current at 50% of the
welding current value with 50% pulse on time. To exit out of the pulse frequency mode, hold down the
Function button (Fig. 2, #13) for approximately 2 seconds until the flashing P Fr disappears.
CELLULOSE ELECTRODE WELDING, 6010 (CEL)
1) Press the Select Mode button (Fig. 2, #2) to switch on the Cellulose Electrode Mode LED (Fig. 2, #4).
2) The display (Fig. 2, #8) will blink CEL for approximately two seconds.
3) The Arc Force Indicator LED (Fig. 2, #10) will illuminate.
4) Use the encoder (Fig. 2, #9) to regulate the welding current shown on the display (Fig. 2, #8).
5) You can adjust the Hot Start value by pressing and holding the Function button (Fig. 2, #13) for several
seconds until the display (Fig. 2, #8) shows HS . Once you see HS , let go of the Function button; the HS
should be replaced by a number between 003 and 040. The number displayed refers to the hot start value
as a percentage. For example, if you weld at 100 amps and set the HS to 003, for a short period of time
after you strike an arc, the welding output is raised to 103 amps. Likewise, if you weld at 100 amps and
set the HS to 040, for a short period of time after you strike an arc, the welding output is raised to 140
amps.
6) Pressing the Function button (Fig. 2, #13) once allows you to select the Arc Force value. The display
(Fig. 2, #8) will blink AF , and then you can select the value with the encoder (Fig. 2, #9). The Arc Force
can be varied from 0% to 500% based on the set welding current value.
7) Pressing the Function button (Fig. 2, #13) again activates the pulse frequency mode. The Pulse Function
Indicator LED (Fig. 2, #12) will blink and the display will read P Fr . By turning the encoder (Fig. 2, #9),
you can vary the frequency value from 0.4Hz to 5Hz. The factory set the base current at 50% of the
welding current value with 50% pulse on time. To exit out of the pulse frequency mode, hold down the
Function button (Fig. 2, #13) for approximately 2 seconds until the flashing P Fr disappears.