background image

lp-220 Rev. 000 Rel. 007 Date 2.12.18

2

The following defined terms are used throughout this manual to 

bring attention to the presence of hazards of various risk levels or to 

important product information.

DANGER 

indicates an imminently hazardous situation which, if not 

avoided, will result in serious personal injury or death.

WARNING 

indicates a potentially hazardous situation which, if not 

avoided, could result in personal injury or death.

CAUTION 

indicates a potentially hazardous situation which, if not 

avoided, may result in moderate or minor personal injury.

CAUTION used without the safety alert symbol 

indicates a 

potentially hazardous situation which, if not avoided, may result in 

property damage.

NOTICE 

is used to address practices not related to personal injury.

Foreword

This manual is intended to be used in conjunction with other literature 

provided with the Evacuated Tube Solar Collector. This includes all 

related control information. It is important that this manual, all other 

documents included with this system, and additional publications, 

such as 

Solar Water Heating System Design and Installation Guidelines, 

SRCC OG-300

, be reviewed in their entirety before beginning any work.

Installation should be made in accordance with the regulations of 

the Authority Having Jurisdiction, local code authorities, and utility 

companies which pertain to this type of water heating equipment.
Authority Having Jurisdiction (AHJ) – The Authority Having Jurisdiction 

may be a federal, state, local government, or individual such as a fire 

chief, fire marshal, chief of a fire prevention bureau, labor department 

or health department, building official or electrical inspector, or others 

having statutory authority. In some circumstances, the property owner 

of his/her agent assumes the role, and at government installations, the 

commanding officer or departmental official may be the AHJ.

NOTE:

 HTP reserves the right to modify product technical specifications 

and components without prior notice.

For the Installer

INSTALLATION OR SERVICE OF THESE SOLAR PANELS IS REQUIRED TO BE 

PERFORMED BY LICENSED PROFESSIONALS WHERE SOLAR, PLUMBING, 

AND ELECTRICAL WORK IS REQUIRED.
The installer should be guided by the instructions furnished with 

the tank, as well as local codes and utility company requirements. 

Preference should be given to codes and requirements where they 

differ from the furnished instructions.
Additional publications which should guide the installer include:

Solar Water Heating System Design and Installation Guidelines, SRCC OG-

300

, available from Solar Rating & Certification Corporation, 400 High 

Table of Contents

Introduction - About Your Solar Collector 

3

Part 1 - General Safety Information 

3

A. When Servicing the Solar Water Heating System 

3

B. Metallic Components 

3

C. Local Installation Regulations 

3

D. Evacuated Tubes 

4

E. High Temperatures 

4

F. Safety Precautions 

4

G. Water Temperature Adjustment 

4

H. System Water 

4

I. Freeze Protection 

4

Part 2 - Important Information 

4

A. Scope of this Manual 

4

B. Local Standards and Authorized Persons 

4

C. Terminology 

5

D. Possible System Designs 

5

1. Open Loop Systems 

5

2. Closed Loop Systems 

5

3. Drain Back Systems 

5

E. Fluid Quality 

5

F. Corrosion 

5

G. Freeze Protection 

5

H. Wind Stress 

5

I. Snow Load 

6

J. Storage Tanks 

6

K. Hail Resistance 

6

Part 3 - Installation Information 

6

A. Transport, Unpacking, and Inspection 

6

B. Collector Dimensions and Weights 

7

C. Tools and Materials 

7

D. System Design 

7

E. Delta-T Controller Settings 

8

F. Stagnation and Overheating 

8

G. Sizing System to Avoid Overheating 

8

H. Collector Angle, Plane, and Direction 

8

1. Collector Direction 

8

2. Collector Angle (Tilt) 

8

3. Collector Plane (Horizontal or Vertical) 

8

I. Avoid Shade 

8

J. Location 

8

K. Expansion Tank 

8

1. Open Loop Systems 

9

2. Closed Loop Systems 

9

3. Drain Back Systems 

9

L. Lightning Protection 

9

M. Pipe Sizing and Connections 

9

N. Connection of Multiple Collectors 

9

O. Potable Water 

9

P. Mounting Frame 

9

Q. Galvanic Reaction 

9

Part 4 - Collector Installation 

9

Part 5 - Roof / Wall Mounting Suggestions 

12

A. Roof Mounting 

12

B. Flush Pitched Roof Installation 

13

1. Tiled Roof Attachment 

13

2. Corrugated Iron Roof Attachment 

13

3. Asphalt Shingle Roof 

13

For your safety, please read through this manual carefully before 

installation to minimize the risk of fire, property damage, personal 

injury, or death. Ensure the solar hot water system is properly 

installed in accordance with this manual before use.

Point Drive, Suite 400, Cocoa, FL 32926-6630, www.solar-rating.org.

Code for the Installation of Heat Producing Appliances

 (latest version), 

available from the American Insurance Association, 85 John Street, 

New York, NY  11038.
The latest version of the 

National Electrical Code, NFPA No. 70

.

In Canada refer to 

Canadian Electrical Code C 22.1

, from Canadian 

Standards Association, 5060 Spectrum Way, Suite 100, Mississauga, 

Ontario, Canada L4W 5N6.

Содержание HP-30SC





















Отзывы: