background image

   HT950N 

 

 

 

 

EN - 16

8. SERVICE 

8.1. WARRANTY 

CONDITIONS 

This equipment is guaranteed against material faults or production defects, in accordance 
with the general sales conditions. During the warranty period (one year), faulty parts may 
be replaced. The manufacturer reserves the right to decide either to repair or replace the 
product. 
 
In case of returning of the instrument, all transport charges must be paid by the customer. 
The instrument must be accompanied by a delivery note indicating the faults or reasons of 
returning. The returned tester must be packed in its original box. Any damage occurred in 
transit because of lack of original packaging will be debited to the customer. 
The manufacturer is not responsible for any damage against persons or things. 
 
The warranty won’t be applied to the following cases: 

  faults due to improper use of the equipment 

  faults due to combination of the tester with incompatible equipment. 

  faults due to improper packaging. 

  faults due to servicing carried out by a person not approved by the company. 

  faults due to modifications made without explicit authorization of our technical 

department. 

  faults due to adaptation to a particular application not provided for by the definition of 

the equipment or by the instruction manual. 

 
The contents of this manual cannot be reproduced in any form without our authorization. 
 
Our products are patented. Our logotypes are registered. We reserve the right to 
modify characteristics and prices further to technological developments.
 
 
8.2. SERVICE 
If the equipment doesn’t work properly, before contacting the SERVICE, test cables and 
Pt100 state and change them if necessary. 
If the equipment still doesn’t work, make sure that your operating procedure complies with 
the one described in this manual. 
In case of returning of the instrument, all transport charges must be paid by the customer. 
The instrument must be accompanied by a delivery note indicating the faults or reasons of 
returning. The returned tester must be packed in its original box. Any damage occurred in 
transit because of lack of original packaging will be debited to the customer. 
 

Содержание HT950N


















Отзывы: