HSP MX40P Скачать руководство пользователя страница 1

Страница: 1 / 16

• Pen / Marker

• Die Grinder & multi tool

• Soapy water solution

• Centre Punch

• Masking Tape

• Allen Key set (Metric)

• Drill & Drill bits

• Scissors & Knife

• Phillips head screwdriver

• Ruler

• Caulking Gun

• Spanner & Socket

• Silicon - Non Acetic

• Tape measure

• Read Instructions fully before commencing installation.

• Clean Tonneau Cover with a mild detergent and water solution

• Do not use abrasive cleaners or solvents

• Refer to manufactures instructions applicable to power drill.

• Protect Tub floor against scratches during installation process.

Check contents of kit before commencing fitment and report any discrepancies

Fitting Instructions Part Number

40P

. Mercedes-Benz X Class

Dual Cab 201

If lubrication of the locks or hinges is required use only Graphite Powder. DO NOT use any other

lubricants or oils.

• Do not stand/sit or rest heavy objects on Tonneau Cover

• Humans or animals are not to be under the closed Tonneau at any given time

• Securely lock tonneau Cover before operating vehicle

• Tonneau Cover is not dust or water tight

• Do not carry open volatile chemicals with Tonneau Cover installed

• If contact with volatile chemicals occur, clean Tonneau with mild detergent and water solution

Tools Required

Maintenance

Care Instructions

IMPORTANT

*Image example shown only

MX40P

Page 1 of 16

Содержание MX40P

















Результаты поиска

Содержание MX40P

Отзывы:

Бренды по названию

Популярные бренды

HSP MX40P, Инструкция по монтажу

Результаты поиска

Содержание MX40P

Отзывы:

Бренды по названию

Популярные бренды