HPE StoreEasy 1X60 Storage Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 183

background image

Getting started

The topic describes the installation requirements and step-by-step instructions for setting up an HPE
StoreEasy 1X60 Storage system.

Installation

Follow the step-by-step instructions to install the HPE StoreEasy 1X60 Storage system:

•

Safety precautions

•

Prerequisites

•

Mounting the system in a rack

•

Cabling instructions

•

•

Complete installation

•

Launch the Initial Configuration Toolkit (ICT)

Safety precautions while installing the rail kits and mounting the system in a
rack

CAUTION:

Electrostatic Discharge (ESD) can damage the electronic components. Ensure that you are properly
grounded (earthed) before beginning any installation procedure.

HPE recommends the following safety precautions:

• Only qualified individuals who know the procedures, precautions, and equipment hazards that contains

hazardous electrical circuits must perform this installation.

• The rail kits, when installed, form only a shelf for the StoreEasy 1X60 to rest on. The StoreEasy 1X60 is

not attached to the rail by any other means. Use extreme caution when pulling the StoreEasy 1X60 out
from the rack. The storage system can slip and fall, which may cause damage or injury to the StoreEasy
1X60 Storage. HPE is not responsible for any damage or injury caused by mishandling of StoreEasy
1X60.

• Ensure that the rack is leveled and stable before working on the rack. The leveling jacks (feet) must

extend to the floor and the full weight of the rack must rest firmly on the floor.

• Ensure that the rack has anti-tip measures, such as floor-bolting, anti-tip feet, ballast, or a combination of

the measures as specified by the rack manufacturer and applicable codes.

• Ensure that sufficient personnel are available to support one or more products during the installation

process. HPE recommends you use an appropriate lifting device as an installation aid.

• Ensure that the rack is loaded from bottom to top, with the heaviest appliances at the bottom to make the

rack steady.

• Avoid overloading the branch circuit that provides power to the rack. The total rack load must not exceed

80 percent of the branch circuit rating.

12

Getting started

«
...
10
11
12
13
14
...
»

Содержание StoreEasy 1X60 Storage
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StoreEasy 1X60 Storage

Бренд: G-Technology Страницы: 51

XCubeDAS XD5324D

Бренд: Qsan Страницы: 49

Бренд: IBM Страницы: 117

TotalStorage DS4200

Бренд: IBM Страницы: 222

Бренд: G-Technology Страницы: 33

CANOPIA RUBICON

Бренд: Palram Страницы: 71

Бренд: Husky Страницы: 14

Бренд: Quantum Страницы: 2

Бренд: Metro DataVac Страницы: 16

Бренд: Seagate Страницы: 2

Бренд: Pioneer Страницы: 32

Бренд: Sun Microsystems Страницы: 40

Бренд: VIOLIN SYSTEMS Страницы: 208

Бренд: BITO Страницы: 64

Бренд: Cavalry Страницы: 16

Бренд: Seagate Technology Страницы: 36

Бренд: LaCie Страницы: 54

Бренд: Power Fist Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды