HPE ProLiant DL180 Скачать руководство пользователя страница 32

Страница: 32 / 172

• Installation by an HPE authorized technical specialist.

• Verification prior to installation that all service prerequisites are met.

• Delivery of the service at a mutually scheduled time convenient to your organization.

• Allows your IT resources to stay focused on their core tasks and priorities.

• Full coverage during the warranty period for products that require installation by an HPE authorized

technical specialist.

For more information on the features, limitations, provisions, and ordering information of the HPE
Installation Service, see this Hewlett Packard Enterprise website:

http://www.hpe.com/support/installation-service

Setting up the server

Prerequisites

Before setting up the server:

• Download the latest SPP:

http://www.hpe.com/servers/spp/download

Support validation required

• Verify that your OS or virtualization software is supported:

http://www.hpe.com/info/ossupport

• Read the HPE UEFI requirements for ProLiant servers on the

Hewlett Packard Enterprise website

If UEFI requirements are not met, you might experience boot failures or other errors when installing
the operating system.

• Obtain the storage driver if needed:

◦ Download it from the HPE Support Center website:

http://www.hpe.com/support/hpesc

◦ Extract it from the SPP.

• Read the operational requirements for the server:

Operational requirements

on page 34

• Read the safety and compliance information on the HPE website:

http://www.hpe.com/support/safety-compliance-enterpriseproducts

Procedure

Unbox the server

Unbox the server and verify the contents:

• Server

• Power cord

Setup

Содержание ProLiant DL180













































































































































































Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды

HPE ProLiant DL180, Руководство пользователя

Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды