manualshive.com logo in svg

HPE Edgeline EL300, Руководство по настройке и конфигурации

Поделиться
Скачать
HPE Edgeline EL300 Скачать руководство пользователя страница 33

9.

Optional: 

Install the SIM card.

10. Remove the LTE gap pad liner from the heat spreader.

11. Install the heat spreader.

12. Install the drive cage cover.

13. Install the security cover.

14. Install the preferred bracket option.

15. Install the LTE antennas.

16. Do one of the following:

•

Mount the system on wall.

•

Mount the system on rails.

17. Connect the power cord to the system.

18. Connect the power cord to the power source.

19. Power up the system.

The installation is complete.

Installing the SIM card

IMPORTANT: The SIM cards are supplied by your preferred mobile broadband provider, and cannot be ordered from
HPE. The SIM cards must be nano-SIM form factor.

The EL300 system supports installation of two SIM cards. The first SIM card must be installed in the primary slot location only.

Wireless network kit and antenna installation

33

Содержание Edgeline EL300




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды