background image

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric 
shock and injury to persons, including the following:

1)Read and understand all instructions.

2)Follow all warnings and instructions marked on the product.

3)Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth 
for cleaning.

4)Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, 
or near a swimming pool.

5)Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

6)Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from overheating these 
openings must not be blocked or covered The openings should never be blocked by placing the product on the bed, sofa, rug or 
other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be 
placed in a built-in installation unless proper ventilation is provided.

7) This product should be operated only from the type of power source indicated on the appliance. If you are not sure of the type 
of power supply to your home, consult your dealer or local power company.

8)Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking 
on it.

9)Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.

10)Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short 
out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

11) To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified service faciI4 when some 
service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect 
reassembly can cause electric shock when the appliance is subsequently used.

12)Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A) When the power supply cord or plug is damaged or frayed. B) If liquid has been spilled into the product.

C)If the product has been exposed to rain or water.

D) 

If the product does not operate normally by following the operating instructions. Adjust only those controls, that are 

covered by the operating instructions because improper adjustment of other controls may result in damage and will often require 
extensive work by a qualified technician to restore the product to normal operation.

E) If the product has been dropped or the cabinet has been damaged. F) If the product exhibits a distinct change in perfor-
mance.

13)Avoid using the product during an electrical storm. There may be a remote risk of electric shock from lightning.

14)Do not use the telephone to report a gas leak in the vicinity of the leak.

INSTALLATION INSTRUCTIONS

1. Never install telephone wiring during a lightning storm.

Содержание YELLOWJACKET PLUS






































Отзывы: