HP Surestore Tape Library Model 3/30 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 62

HP Surestore Tape Library Model 3/30 Скачать руководство пользователя страница 43

DLT Library

4–1

Chapter 4.
Handling Cartridge Tapes

Generally observe the following protocols when handling cartridge tapes:

S

Keep cartridges clean.

S

Inspect cartridges before each use.

S

Never put a damaged cartridge into a drive or storage cell.

S

Do not open cartridges or release the cartridge latch and pull out tape.

S

Do not handle tape that is outside the cartridge.

S

Do not expose the tape or cartridge to direct sunlight or moisture.

S

Do not expose a recorded cartridge to magnetic fields.

Inspecting Cartridge Tapes

A defective or dirty cartridge tape can damage a drive. If you suspect a problem
with a cartridge, inspect it for these defects:

S

Cracked or broken cartridge

S

Broken cartridge latch

S

Broken cartridge leader

S

Damaged write protect switch

S

Labels not firmly or neatly attached

Figure 4–1.

Inspecting a Cartridge

«
...
41
42
43
44
45
...
»

Содержание Surestore Tape Library Model 3/30































































Отзывы:

Нет отзывов