HP Surestore Tape Library Model 3/30 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 62

HP Surestore Tape Library Model 3/30 Скачать руководство пользователя страница 41

Hardware Operator’s Guide

Manual Operations

DLT Library

3–11

Table 3–1.

Tape Drive LEDs (right front panel)

Label

Color

State

Operating Condition

Write Protected

Orange

On
Off

Tape is write protected
Tape is write enabled

Tape In Use

Yellow

Blinking
On

Tape is moving
Tape is loaded: ready for use

Use Cleaning
Tape

Yellow

On

Remains on after you unload
the cleaning tape

After cleaning, turns on
again when you reload the
data cartridge

Off

Drive head needs cleaning, or
the tape is bad

Cleaning tape attempted to
clean the drive head, but the
tape has expired, so cleaning
was not done.

Problem data cartridge. Try
another cartridge. If problem
persists, notify your service
representative.

Cleaning is complete, or
unnecessary

Operate Handle

Green

On

Off

Blinking

Okay to operate the load latch.

Do not operate the load latch.

Close the drive (load latch in
down position) and wait for a
steady on green.

The LEDs on the left front face of the tape drives are yellow and indicate the tape
format. For example, if the 20.0 light is on, the tape is recorded in 20.0 GB
density. If the light is blinking, the tape is recorded in a different density although
this density was selected.

Refer to the documentation that accompanies your tape drives for more detailed
information.

«
...
39
40
41
42
43
...
»

Содержание Surestore Tape Library Model 3/30































































Отзывы:

Нет отзывов