manualshive.com logo in svg

HP Surestore Disk Array 12h - And FC60, Руководство по установке

Поделиться
Скачать
HP Surestore Disk Array 12h - And FC60 Скачать руководство пользователя страница 9

 
 
 
 
 
 
 
 
 

 

9 

 
 
 
 
 
 
 

Figure 3. Replacing an Array Controller Flowchart 

Replacing an Array Controller

NOTE:  In some cases, you may need to download firmware when replacing a controller.

Downloading firmware is an offline process.  In most cases, the LUNs on the array need

to be either un-mounted or deactivated from the volume group.

No

Does the replacement

controller have the same

firmware that is in the disk

array?

Perform procedure "

Replace A

"

Replacing controller and firmware

matches

(replace matching)

Yes

Is the disk array a

boot device?

Perform procedure "

Replace C

"

Replacing controller on boot device

and firmware does NOT match

(replace boot)

Perform procedure "

Replace B

"

Replacing controller and firmware

does NOT match

(replace non boot)

Yes

No

Does this disk

array have a single

controller?

Yes (Single Controller)

No

(Dual Controller)

Perform procedure "

Replace D

"

Replacing a Single Controller

(replace single)

 

Содержание Surestore Disk Array 12h - And FC60




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды