HP StorageWorks 2/64 - Core Switch Скачать руководство пользователя страница 25

Страница: 25 / 830

Fabric OS 5.x command reference guide

Resets the SNMP agent configuration to default values.

Synopsis

agtcfgdefault

Availability

admin

Description

Use this command to reset the SNMP agent configuration with the switch default values.

This command prompts the user and proceeds to reset only on the user’s confirmation. All new values

successfully configured by the command take effect immediately. These changes are persistent across

power cycles and reboots. For dual-domain systems,

agtCfgDefault

operates on the SNMP agent

associated with the current switch.

This command resets the following values (See the

HP StorageWorks Fabric OS 5.x MIB reference guide

for detailed

sysDescr

sysLocation

, and

sysContact

descriptions):

There are six communities and respective trap recipients supported by the agent. The first three

communities are for read-write (rw) access and the last three are for read-only (ro) access. The default

value for the trap recipient of each community is 0.0.0.0. The default values for the community strings are

as follows:

•

Community 1: Secret Code

•

Community 2: OrigEquipMfr

•

Community 3: private

•

Community 4: public

•

Community 5: common

•

Community 6: FibreChannel

For an SNMP management station to receive a trap generated by the agent, the administrator must

configure a trap recipient to correspond to the IP address of the management station. In addition, the trap

recipient must be able to pass the access control list (ACL) check.

Trap recipient severity level

The trap severity level is associated with each trap recipient IP address. The event trap level is in

conjunction with the event's severity level. When an event occurs and if its severity level is at or below the

set value, the SNMP event traps (

swEventTrap

swFabricWatchTrap

, and

connUnitEventTrap

)

agtCfgDefault

sysDescr

The system (switch) description. The default value is Fibre Channel Switch in most

platforms; however, the default system description value is platform-specific.

Different values might appear as the default for some specialized platforms.

sysLocation

The location of the system. The default value is End User Premise.

sysContact

The contact information for the system. The default value is Field Support.

authTraps

When enabled, the authentication trap, authenticationFailure, is transmitted to a

configured trap recipient in the event the agent received a protocol message that

is not properly authenticated. In the context of SNMPv1 and SNMPv2c, this

means that a request contains a community string that is not known to the agent.

The default value for this parameter is 0 (disabled).

Содержание StorageWorks 2/64 - Core Switch































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание StorageWorks 2/64 - Core Switch

Отзывы:

Похожие инструкции для StorageWorks 2/64 - Core Switch

Бренды по названию

Популярные бренды

HP StorageWorks 2/64 - Core Switch, Справочник по командам

Результаты поиска

Содержание StorageWorks 2/64 - Core Switch

Отзывы:

Похожие инструкции для StorageWorks 2/64 - Core Switch

Бренды по названию

Популярные бренды