HP StorageWorks 2/64 - Core Switch Скачать руководство пользователя страница 125

Страница: 125 / 830

Fabric OS 5.x command reference guide 125

NOTE:

The R_A_TOV, E_D_TOV, WAN_TOV, and MAX_HOPS configuration parameters are

inter-related. Assigning a specific value to one or more of these parameters can change the range of

allowed values that can be assigned to the other parameters. As a result, the user might not be able to set

all the values within the range displayed against each parameter. To reduce problems, the configuration

utility validates the modified parameter values and prompts the user to re-enter some values, if the

validation check fails.

MAX_HOPS

Maximum hops (MAX_HOPS) is an integer that denotes the

upper limit on the number of hops a frame might have to traverse

to reach any destination port from any source port across the

fabric.

Data Field Size

The data field size specifies the largest possible value, in bytes, and

advertises this value to other switches in the fabric during construction

of the fabric as well as to other devices when they connect to the

fabric. Setting this to a value smaller than 2112 might result in

decreased performance.

Sequence-Level Switching

When sequence-level switching is set to 1, frames of the same

sequence from a particular source are transmitted as a group. When

this feature is set to 0, frames are transmitted interleaved among

multiple sequences.

Under normal conditions, sequence-level switching should be disabled

for better performance. However, some host adapters have

performance issues when receiving interleaved frames from multiple

sequences. When there are such devices attached to the fabric,

sequence-level switching should be enabled.

Disable Device Probing

When disable device probing is set to 1, devices that do not register

with the name server are not present in the name server data base. Set

this mode only if the switch N_Port discovery process (PLOGI, PRLI,

INQUIRY) causes an attached device to fail.

Suppress Class F Traffic

When this mode is set to 1, all Class F interswitch frames are

transmitted as Class 2 frames. This is to support remote fabrics that

involve ATM gateways, which don't support class F traffic.

Switch PID Format

The formats are as follows:
0

Native PID format (16 based, 16 port format), for fabrics

with legacy low-count-port switches.

Core PID format (0 based, 256 port format), preferred

mode for mixed fabrics with legacy and new switches.

Extended edge PID format (16 based, 256 port format),

used in mixed fabrics with legacy and new switches to

avoid need to reboot host systems when static PID binded is

used.

Per-frame Route Priority

In addition to the eight virtual channels used in frame routing priority,

support is also available for per-frame-based prioritization when this

value is set. When Per-frame Route Priority is set to 1, the virtual

channel ID is used in conjunction with a frame header to form the final

virtual channel ID.

Long Distance Fabric

When this mode is set to 1, ISLs in a fabric can be up to 100 km long.

The exact distance level is determined by the per-port configuration on

the E_Ports of each ISL. Both E_Ports in an ISL must be configured to run

the same long-distance level; otherwise, the fabric will be segmented.

The Extended Fabric License is required to set this mode.

Содержание StorageWorks 2/64 - Core Switch































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание StorageWorks 2/64 - Core Switch

Отзывы:

Похожие инструкции для StorageWorks 2/64 - Core Switch

Бренды по названию

Популярные бренды

HP StorageWorks 2/64 - Core Switch, Справочник по командам

Результаты поиска

Содержание StorageWorks 2/64 - Core Switch

Отзывы:

Похожие инструкции для StorageWorks 2/64 - Core Switch

Бренды по названию

Популярные бренды