HP ProLiant DL388 Скачать руководство пользователя страница 110

Страница: 110 / 127

Specifications 110

Specifications

Environmental specifications

Specification

Value

Temperature range*

Operating

C to 35

C (50

F to 95

Shipping

-30

C to 50

C (-22

F to 122

Storage

-30°C to 60°C (-22°F to 140°F)

Maximum wet bulb
temperature

C (82.4

Relative humidity

(noncondensing)**

Operating

10% to 90%

Non-operating

5% to 95%

* All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to 3048

m (10,000 ft) is applicable. No direct sunlight allowed.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C (113°F). Altitude maximum for

storage corresponds to a pressure minimum of 70 KPa.

Mechanical specifications

Specification

Value

Dimensions

Height

8.59 cm (3.38 in)

Depth

66.07 cm (26.01 in)

Width

44.54 cm (17.54 in)

Weight (maximum)

27.2 kg (60.0 lb)

Weight (no drives installed)

20.4 kg (47.2 lb)

Power supply specifications

Depending on installed options, the server is configured with one of the following power supplies:

•

HP ProLiant 1200 W Power Supply

Specification

Value

Input requirements

Rated input voltage

100 to 120 VAC, 200 to

240 VAC

Rated input frequency

50 Hz to 60 Hz

Содержание ProLiant DL388
































































































































Результаты поиска

Содержание ProLiant DL388

Отзывы:

Бренды по названию

Популярные бренды

HP ProLiant DL388, Руководство пользователя

Результаты поиска

Содержание ProLiant DL388

Отзывы:

Бренды по названию

Популярные бренды