HP ProLiant BL460c Gen9 Скачать руководство пользователя

Страница: 9 / 90

Component identification 9

Hot-plug drive LED definitions

Item LED

Status

Definition

Locate

Solid blue

The drive is being identified by a host application.

Flashing blue

The drive carrier firmware is being updated or requires an
update.

Activity ring

Rotating green

Drive activity

Off

No drive activity

Do not remove

Solid white

Do not remove the drive. Removing the drive causes one or
more of the logical drives to fail.

Off

Removing the drive does not cause a logical drive to fail.

Drive status

Solid green

The drive is a member of one or more logical drives.

Flashing green

The drive is rebuilding or performing a RAID migration, strip size
migration, capacity expansion, or logical drive extension, or is
erasing.

Flashing
amber/green

The drive is a member of one or more logical drives and predicts
the drive will fail.

Flashing amber The drive is not configured and predicts the drive will fail.

Solid amber

The drive has failed.

Off

The drive is not configured by a RAID controller.

IMPORTANT:

The Dynamic Smart Array B140i Controller is only available in UEFI Boot

Mode. It cannot be enabled in Legacy BIOS Boot Mode. If the B140i controller is disabled,
drives connected to the system board Mini-SAS connectors operate in AHCI or Legacy mode.
Under this condition:

•

The drives cannot be a part of a hardware RAID or a logical drive.

•

The Locate, Drive status, and Do not remove LEDs of the affected drives are not controlled

and will retain their last configured state. HPE SmartDrives preserve the last configured state
across power cycles.

Содержание ProLiant BL460c Gen9



























































































Результаты поиска

Содержание ProLiant BL460c Gen9

Отзывы:

Похожие инструкции для ProLiant BL460c Gen9

Бренды по названию

Популярные бренды

HP ProLiant BL460c Gen9, Руководство пользователя

Результаты поиска

Содержание ProLiant BL460c Gen9

Отзывы:

Похожие инструкции для ProLiant BL460c Gen9

Бренды по названию

Популярные бренды