HP ProLiant BL p-Class GbE2 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 126

background image

2

Menu Basics

Introduction

The HP ProLiant BL p-Class GbE2 Interconnect Switch CLI is used for viewing switch
information and statistics. In addition, the administrator can use the CLI for performing all
levels of GbE2 Interconnect Switch configuration.

To make the CLI easy to use, the various commands have been logically grouped into a series
of menus and submenus. Each menu displays a list of commands and/or submenus that are
available, along with a summary of what each command will do. Below each menu is a
prompt where you can enter any command appropriate to the current menu.

This chapter describes the

Main Menu

commands, and provides a list of commands and

shortcuts that are commonly available from all the menus within the CLI.

The Main Menu

The

Main Menu

displays after a successful connection and login. The following table shows

the

Main Menu

for the administrator login. Some features are not available under the user

login.

[Main Menu]
info - Information Menu
stats - Statistics Menu
cfg - Configuration Menu
oper - Operations Command Menu
boot - Boot Options Menu
maint - Maintenance Menu

diff - Show pending config changes [global command]
apply - Apply pending config changes [global command]
save - Save updated config to FLASH [global command]
revert - Revert pending or applied changes [global command]
exit - Exit [global command, always available]

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

2-1

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:48 PM

«
...
14
15
16
17
18
...
»

Содержание ProLiant BL p-Class GbE2































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProLiant BL p-Class GbE2

Бренд: Quick Страницы: 28

SmartSwitch 6500

Бренд: Cabletron Systems Страницы: 150

MMAC-Plus 9H421-12

Бренд: Cabletron Systems Страницы: 38

Бренд: Cabletron Systems Страницы: 86

MMAC-Plus 9T125-24

Бренд: Cabletron Systems Страницы: 30

7C03 MMAC SmartSWITCH

Бренд: Cabletron Systems Страницы: 16

Sierra Video 1208V3S

Бренд: Kramer Страницы: 2

Бренд: H3C Страницы: 57

Бренд: Eaton Страницы: 2

Бренд: Black Box Страницы: 2

Бренд: Labgear Страницы: 8

Бренд: A-Neuvideo Страницы: 16

SwitchMan USB-Combo SW4

Бренд: Raritan Страницы: 2

Бренд: Kathrein Страницы: 41

CheetaHub Power-3004E

Бренд: Accton Technology Страницы: 11

Power Switch G0021

Бренд: G-Force Страницы: 2

Бренд: Altinex Страницы: 14

Бренд: PS Engineering Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды