HP OmniBook 4100 Скачать руководство пользователя страница 28

Страница: 28 / 88

2-8

Removal and Replacement

HP OmniBook 4100

Removing the Keyboard

(HP Authorized Service Providers Only)

Required Equipment

•

Small Phillips screwdriver.

•

Probe or tweezers.

Removal Procedure

1. Unplug the ac adapter, if present, and remove the battery.

2. On the bottom of the unit, remove the seven “K” screws from the bottom case.

3. Insert your small finger into the PCMCIA opening and push up the top of the keyboard—or you

can lift it from above using a thin flat-blade screwdriver. After lifting the back edge slightly, slide
the keyboard toward the back until the front-left corner is free.

4. With the display tilted only slightly back, lift the front of the keyboard and lean it back against the

display. Be careful not to scratch the display or pull on the cables.

5. Release the pointing stick flex cable from the VGA PCA.

6. Release the keyboard flex cable from the VGA PCA.

Figure 2-5. Removing the Keyboard

Keyboard and
pointing stick
flex cables

Strip cover

Pointing stick cap

Screw, M2.5×16mm (7)

Содержание OmniBook 4100

























































































Результаты поиска

Содержание OmniBook 4100

Отзывы:

Похожие инструкции для OmniBook 4100

Бренды по названию

Популярные бренды

HP OmniBook 4100, Руководство по обслуживанию

Результаты поиска

Содержание OmniBook 4100

Отзывы:

Похожие инструкции для OmniBook 4100

Бренды по названию

Популярные бренды