HP OmniBook 4100 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 88

background image

HP OmniBook 4100

Removal and Replacement

2-7

3. Reboot the computer. If you are using the Recovery CD, press ESC during reboot to cancel the

OmniBook screen, ESC to display the boot-device menu, then select the CD-ROM drive as the
boot device.

4. When prompted, select “Create Hibernate Partition.”

We recommend that you create a 96-MB partition, the same as the factory setup.

Replacing Small Parts

(User-Replaceable)

The following small parts are user-replaceable.

Table 2-6. Replacing Small Parts (User-Replaceable)

Part

Replacement Procedure

Docking Doors

Open each door and flex the door until one side tab releases. To replace, see the
picture on page 2-19.

Feet

Insert a small flat-blade screwdriver under the foot and pry it loose. To replace, firmly
press the adhesive side of the foot into the recess.

I/O Door

With the door closed, insert a small flat-blade screwdriver behind the door from
below. Flex the door until one side tab releases. It helps to press in lightly on the
ends of the door.

Pointing Stick Cap

Pull the cap off the pointing stick.

RAM/BIOS Cover

On the bottom of the unit, remove the two screws from the RAM/BIOS cover and
remove the cover.

VGA Connector Cover

With the display closed, push up on the cover and down on the bottom case until the
lower tabs release. To install, insert the top tabs into the strip cover, then push up on
the cover and down on the bottom case until you can insert the lower tabs.

«
...
25
26
27
28
29
...
»

Содержание OmniBook 4100

























































































Отзывы:

Нет отзывов

Похожие инструкции для OmniBook 4100

Бренд: IHP Страницы: 8

Бренд: WÄRTSILÄ Страницы: 64

Fast PLUG 500 premium

Бренд: SAGEMCOM Страницы: 2

Бренд: Tait Страницы: 46

Бренд: Tait Страницы: 9

Бренд: Tait Страницы: 89

Бренд: Tait Страницы: 20

Бренд: X10 Страницы: 1

Бренд: NATURE & DECOUVERTES Страницы: 13

Toughbook CF-52EKMBDAM

Бренд: Panasonic Страницы: 2

Бренд: Yakima Страницы: 6

Бренд: Yakima Страницы: 18

Бренд: Yakima Страницы: 18

Toughbook CF-Y5LWEZABM

Бренд: Panasonic Страницы: 40

Бренд: Zebronics Страницы: 6

Бренд: iArmor Страницы: 6

Бренд: BGS technic Страницы: 5

Бренд: PCB Piezotronics Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды