HP J4861A Скачать руководство пользователя | Manualshive

Страница: 71 / 94

background image

Switch Ports and Network Cables

Twisted-Pair Cable/Connector Pin-Outs

Fiber-Optic Cables

Port Type

Cable Specifications

Connector Type

Maximum Length

Gigabit-SX

62.5/125 mm or 50/125

µ

m (core/cladding)

diameter, graded-index, low metal content,
multimode fiber-optic cables, complying
with the ITU-T G.651 and ISO/IEC 793-2 Type
A1b or A1a respectively.

LC

- Gigabit-SX

mini-GBIC

SC

- Gigabit-SX

transceiver

•

62.5

µ

m cable:

– 160 MHz*km=220 meters
– 200 MHz*km=275 meters

•

50

µ

m cable:

– 400 MHz*km=500 meters
– 500 MHz*km=550 meters

Gigabit-LX

9/125

µ

m (core/cladding) diameter, graded-

in1310 nm, low metal content, single mode
fiber-optic cables, complying with the ITU-T
G.652 and ISO/IEC 793-2 Type B1 standards.
OR
the multimode fiber-optic cables listed for
Gigabit-SX.

LC

- Gigabit-LX

mini-GBIC

SC

- Gigabit-LX

transceiver

•

single-mode cable:

10 kilometers

•

Multimode cable:

550 meters

Note: To use multimode cables for Gigabit-LX, a mode conditioning patch cord may be needed - See the

Installation Guide

that came with your module for more information.

Gigabit-LH

9/125 mm (core/cladding) diameter, graded-
in1310 nm, low metal content, single mode
fiber-optic cables, complying with the ITU-T
G.652 and ISO/IEC 793-2 Type B1 standards.

LC

- Gigabit-LH

mini-GBIC

70 kilometers

Note:

Between the transmit and receive ends of the cable, at least 5db of attenuation is required for a

reliable connection. This is equivalent to 20Km of the fiber-optic cable. For distances less than 20Km,
you must add attenuators to bring the total attenuation to at least 5db. Most cable vendors carry
attenuators.

Twisted-Pair Cable/Connector Pin-Outs

The HP Auto-MDIX Feature:.

In the

default configuration

, “Auto”, the

10/100Base-TX ports on the 10/100-TX gl Module that is used in the Series
4100gl Switches all automatically detect the type of port on the connected
device and operate as either an MDI or MDI-X port, whichever is appropriate.
So for any connection, a straight-through twisted-pair cable can be used --

you

no longer have to use crossover cables

, although crossover cables can also be

used for any of the connections. The 100/1000-T gl Module, and the
100/1000-T Transceiver supports the IEEE 802.3ab standard, which includes
the “Auto MDI/MDI-X” feature, which operates the same way.

Ca
ble
s

Swi

tch Ports an

d Net

w

o

rk

B-3

«
...
69
70
71
72
73
...
»

Содержание J4861A































































































Отзывы:

Нет отзывов

Похожие инструкции для J4861A

Бренд: NETGEAR Страницы: 15

Бренд: Vector Страницы: 6

DSR Series DSR1030

Бренд: Avocent Страницы: 8

Signature ANTENNA GENIUS 8x2 v2 PLUS

Бренд: 4O3A Страницы: 57

Бренд: Accton Technology Страницы: 7

Бренд: CYP Страницы: 68

S5130-EI Series

Бренд: H3C Страницы: 32

Бренд: YOKOGAWA Страницы: 74

Бренд: IOGear Страницы: 40

OMNICUBE F1DK102P

Бренд: Belkin Страницы: 21

Бренд: Black Box Страницы: 2

Бренд: Gefen Страницы: 48

Бренд: HB Products Страницы: 6

Бренд: LevelOne Страницы: 40

Бренд: Elk Products Страницы: 2

Бренд: Kramer Страницы: 4

Бренд: iNels Страницы: 4

Бренд: Knightsbridge Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды