HP J4861A Скачать руководство пользователя

Страница: 26 / 94

Installing the Series 4100gl Switches

Installation Procedures

Port Type

Cable Type

Length Limits

Fiber Optic Cables

Gigabit-SX

Multimode fiber-optic cables fitted with LC

220 meters to 550 meters depending on the

(on Gigabit-SX-LC

connectors

cable used. See “Fiber-Optic Cables” on

page

mini-GBIC)

B-3

for more information.

Gigabit-LX

Single-mode fiber-optic cables fitted with LC

• single-mode cable = 10 kilometers

(on Gigabit-LX-LC

connectors.

• multimode cable = 550 meters

mini-GBIC)

The multimode cables specified for the Gigabit-
SX mini-GBIC may also be used, but a mode-
conditioning patch cord may be needed — See
the

Installation Guide

that came with your

module for more information.

Installing the Series 4100gl

ches

Gigabit-LH

The same single-mode fiber-optic cables as for

• 70 kilometers

(on Gigabit-LH-LC

Gigabit-LX.

mini-GBIC)

Note:
Gigabit-LH

- Between the transmit and receive ends of the cable, at least 5db of attenuation is required for a reliable

connection. This is equivalent to 20Km of the fiber-optic cable. For distances less than 20Km, you must add attenuators
to bring the total attenuation to at least 5db. Most cable vendors carry attenuators.

Installation Location

Before installing the switch, plan its location and orientation relative to other
devices and equipment:

■

In the front of the switch, allow at least 7.6 cm (3 inches) of space for the
twisted-pair and fiber-optic cabling.

■

In the back of the switch, allow at least 10.2 cm (4 inches) of space for the
power cord and cooling.

■

On the sides of the switch, leave at least 7.6 cm (3 inches) for cooling.

2-6

Содержание J4861A































































































Результаты поиска

Содержание J4861A

Отзывы:

Похожие инструкции для J4861A

Бренды по названию

Популярные бренды

HP J4861A, Руководство по установке и началу работы

Результаты поиска

Содержание J4861A

Отзывы:

Похожие инструкции для J4861A

Бренды по названию

Популярные бренды