manualshive.com logo in svg

HP J3108A, Руководство по установке

Поделиться
Скачать
HP J3108A Скачать руководство пользователя страница 23

15

Removing or Replacing a Module

Removing or Replacing a Module

You can perform this procedure while the Switch 2000 is running.

Figure 8.

 Removing the Module

1.

Remove any network cables from the ports on the module.

2.

Disengage the module’s extractor handle screws from the switch chassis.

3.

Simultaneously rotate both extractor handles downward and pull the 
module toward you until it releases from the slot and the Fault and status 
LEDs for that slot are off.

N o t e

During removal (or installation) the module and switch connectors will 
momentarily be only partially connected. The Fault LED for the slot flashes 
rapidly to indicate this state until the module is removed or properly installed.   
(The other modules in the switch will continue to forward packets normally, 
but other switch functions will be suspended until the module is removed or 
properly installed.)

Disengage These Two Screws

Содержание J3108A









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды